cancel
Showing results for 
Search instead for 
Did you mean: 

PC Graphics

Endlzz
Journeyman III

6800xt

Hi i have a 6800xt, yesterday i update my graphic card and now pc won't start

No display detected.... 

0 Likes
10 Replies
Anoriand
Adept I

Can you test the GPU with another PC? Did you completely uninstall your previews driver from the old card and did a clean install (sometimes leftover files can cause huge errors)? Try your old card and see if you have the same problem. If you don't have your old card, try getting into bios and start windows in safe mode. Worst case scenarios do a CMOS reset followed by a windows reinstall.

The Super Saiyan barrier... Yeah, I've gone far beyond that!
0 Likes
armirol
Adept I

What do you mean by update? Replace the graphics card or update the drivers or update the GC firmware?

Verify you connected the monitor to the graphics card (not to the motherboard HDMI)!
If you replaced the graphics card, most likely it is a seating/power cable issue... try to reseat the GC into the PCIe slot and verify your power cables are all correctly connected. Verify your PSU can deliver enough power (though 6800XT is not too much power hungry)
If it is a driver issue, start your PC and after few seconds press the on/off button until it turns off... after 3 (4?) times, it should start automatically into safe mode.. see if there is an issue with the driver. Use DDU tin safe mode to completely remove the old driver and install the latest one.
If it is a firmware update, the issue might be a lot more difficult to solve....

Hi, driver update... 

0 Likes

So... the PC doesn't start just after upgrading the GC driver? Not light, not fan running, nothing...
Or do you have no signal to the monitor or just a blank screen with a cursor? but the PC is on?

0 Likes

All works fans work to but no display signal 

0 Likes

Not even during boot? Nothing on the screen...no BIOS post code?

If you can go into the BIOS, verify the graphics in on auto or discrete is selected. 

I would try to reseat the GC into its PCIe slot and verify the power cables... maybe connect to another power outlet from the PSU/use a new power cable from PSU to GC.

0 Likes

No bios because no signal in monitor 

0 Likes

And sometimes board white light boot 

0 Likes
ThreeDee
Paragon

check your power supply and/or your UPS if you are plugged into one

List your complete PC specs including make/model of your power supply

reseat everything .. GPU, CPU, RAM, power connections to motherboard and GPU


ThreeDee PC specs
0 Likes
shadow007
Adept III

First unplug Power supply by pulling a Cord from back of your PC then remove DP/HDMI Cable from Graphics Card!!! Now hold the PWR Button on your PC for 10 Sec. then release,reinsert Power supply Cable followed by reinsert DP/HDMI Cable, now turn on your PC. If this doesn't reset to BIOS Default by pressing a Reset Button in your Mobo.

MOBO :EVGA X299 DARK 151-SX-E299-KR CPU : Intel Core i9-10900X Skylake-X 10-Core 3.7 GHz LCR :Corsair Hydro Series H80i V2 GPU :SAPPHIRE NITRO+ RX 6900 XT SE MEMORY: CORSAIR Dominator Platinum SE Torque 32GB (4 x 8GB) CMD32GX4M4C3200C14T SSD 01: SAMSUNG 970 PRO M.2 1 TB NVMe PCI-Express 3.0 x4 MZ-V7P512BW SSD 02: SAMSUNG 860 PRO 256GBX2 Raid 0 PSU : Corsair AX1200I 1200 Watts CASE :Thermaltake (Armor+) VH6000SWA SC :Creative Sound Blaster AE-9 5.1 Channels Monitor Acer XR382CQK IPS 3840x1600 @ 75HZ BD Samsung SH-B123L
0 Likes