27 Replies Latest reply on Sep 18, 2018 6:56 AM by brauliobo

    Ryzen 2500u limited to max. 2000mhz in Linux

    brauliobo

      It wasn't until the latest firmware update (linux-firmware) or kernel 4.17

       

      The system is much slower with this frequency limitation!

       

      On Windows it still can go up to 3ghz.

       

      ~ LANG=en lscpu
      Architecture:        x86_64
      CPU op-mode(s):      32-bit, 64-bit
      Byte Order:          Little Endian
      CPU(s):              8
      On-line CPU(s) list: 0-7
      Thread(s) per core:  2
      Core(s) per socket:  4
      Socket(s):           1
      NUMA node(s):        1
      Vendor ID:           AuthenticAMD
      CPU family:          23
      Model:               17
      Model name:          AMD Ryzen 5 2500U with Radeon Vega Mobile Gfx
      Stepping:            0
      CPU MHz:             1650.764
      CPU max MHz:         2000.0000
      CPU min MHz:         1600.0000
      BogoMIPS:            3992.70
      Virtualization:      AMD-V
      L1d cache:           32K
      L1i cache:           64K
      L2 cache:            512K
      L3 cache:            4096K
      NUMA node0 CPU(s):   0-7
      Flags:               fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good
      nopl nonstop_tsc cpuid extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 movbe popcnt aes xsave avx f16c rdrand lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a m
      isalignsse 3dnowprefetch osvw skinit wdt tce topoext perfctr_core perfctr_nb bpext perfctr_llc mwaitx hw_pstate sme ssbd sev ibpb vmmcall fsgsbase bmi1 avx2 smep bmi2 rdseed adx smap clflus
      hopt sha_ni xsaveopt xsavec xgetbv1 xsaves clzero irperf xsaveerptr arat npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold avic v_vmsave_vml
      oad vgif overflow_recov succor smca

        • Re: Ryzen 2500u limited to max. 2000mhz in Linux
          misterj

          brauliobo, I know almost nothing about Linux, but this sounds like a Linux issue to me.  I suggest you ask in an Linux forum.  Enjoy, John.

          • Re: Ryzen 2500u limited to max. 2000mhz in Linux
            tolinbran

            Which distro are you using out of interest?

             

            Try booting from an older kernel if you still have them installed, should be selectable from the grub bootloader. If it reports the correct max speed then it is likely a bug in the newer kernel, if it still reports the lower speed then it might be an issue with the linux-firmware update.

             

            Another possibility could be the amd64-microcode package, one of the recent patches for spectre v2 vulnerabilities may be the culprit.

              • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                brauliobo

                I'm using archlinux here

                 

                I don't have an older kernel available to boot.

                 

                I'll try removing the amd 17th family microcode later to see if it works (file added at kernel/git/firmware/linux-firmware.git - Repository of firmware blobs for use with the Linux kernel)

                  • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                    abucodonosor

                    brauliobo

                     

                    the output of lscpu is correct.

                     

                    Your CPU has a max frequency of 2GHz and max Turbo frequency of 3.6 Ghz.

                    Linux never shows anythig about Turbo max frequency but a max of your CPU specs.

                     

                    That does not means Turbo  frequency is not working. It does if your system need it.

                     

                    What you want is to play with cpupower util and set everything to performance

                    if you don't care about battery live.

                     

                    Here an example of turbo kicking in why compiling on my EPYC workstation:

                     

                    crazy@ant:~$ lscpu
                    Architektur:                   x86_64
                    CPU Operationsmodus:           32-bit, 64-bit
                    Byte-Reihenfolge:              Little Endian
                    CPU(s):                        64
                    Liste der Online-CPU(s):       0-63
                    Thread(s) pro Kern:            2
                    Kern(e) pro Socket:            16
                    Sockel:                        2
                    NUMA-Knoten:                   8
                    Anbieterkennung:               AuthenticAMD
                    Prozessorfamilie:              23
                    Modell:                        1
                    Modellname:                    AMD EPYC 7281 16-Core Processor
                    Stepping:                      2
                    CPU MHz:                       2612.645
                    Maximale Taktfrequenz der CPU: 2100,0000
                    Minimale Taktfrequenz der CPU: 1200,0000
                    BogoMIPS:                      4193.72
                    Virtualisierung:               AMD-V
                    L1d Cache:                     32K
                    L1i Cache:                     64K
                    L2 Cache:                      512K
                    L3 Cache:                      4096K
                    NUMA-Knoten0 CPU(s):           0-3,32-35
                    NUMA-Knoten1 CPU(s):           4-7,36-39
                    NUMA-Knoten2 CPU(s):           8-11,40-43
                    NUMA-Knoten3 CPU(s):           12-15,44-47
                    NUMA-Knoten4 CPU(s):           16-19,48-51
                    NUMA-Knoten5 CPU(s):           20-23,52-55
                    NUMA-Knoten6 CPU(s):           24-27,56-59
                    NUMA-Knoten7 CPU(s):           28-31,60-63
                    Markierungen:                  fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc cpuid extd_apicid a
                    md_dcm aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 movbe popcnt aes xsave avx f16c rdrand lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw skinit wdt tce topoext perfctr_core perfctr_
                    nb bpext perfctr_llc mwaitx cpb hw_pstate sme ssbd sev ibpb vmmcall fsgsbase bmi1 avx2 smep bmi2 rdseed adx smap clflushopt sha_ni xsaveopt xsavec xgetbv1 xsaves clzero irperf xsaveerptr arat npt lbrv svm_lock nrip_save tsc_scale vmcb_
                    clean flushbyasid decodeassists pausefilter pfthreshold avic v_vmsave_vmload vgif overflow_recov succor smca

                     

                    Noticed the Max and Current running frequency ..

                     

                     

                      • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                        brauliobo

                        I'm sure my CPU frequency never exceeds 2000mhz, /proc/cpuinfo and others confirms that under full load

                          • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                            abucodonosor

                            Ok post output of :

                             

                            cpupower frequency-info

                            cpupower idle-info

                             

                            dmesg >mydmesg.log ( and attach here )

                              • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                brauliobo

                                ~ LANG=en cpupower frequency-info
                                analyzing CPU 0:
                                  driver: acpi-cpufreq
                                  CPUs which run at the same hardware frequency: 0
                                  CPUs which need to have their frequency coordinated by software: 0
                                  maximum transition latency:  Cannot determine or is not supported.
                                  hardware limits: 1.60 GHz - 2.00 GHz
                                  available frequency steps:  2.00 GHz, 1.70 GHz, 1.60 GHz
                                  available cpufreq governors: performance schedutil
                                  current policy: frequency should be within 1.60 GHz and 2.00 GHz.
                                                  The governor "schedutil" may decide which speed to use
                                                  within this range.
                                  current CPU frequency: Unable to call hardware
                                  current CPU frequency: 2.00 GHz (asserted by call to kernel)
                                  boost state support:
                                    Supported: no
                                    Active: no


                                ~ LANG=en cpupower idle-info
                                CPUidle driver: acpi_idle
                                CPUidle governor: menu
                                analyzing CPU 0:

                                Number of idle states: 3
                                Available idle states: POLL C1 C2
                                POLL:
                                Flags/Description: CPUIDLE CORE POLL IDLE
                                Latency: 0
                                Usage: 19603
                                Duration: 926649
                                C1:
                                Flags/Description: ACPI HLT
                                Latency: 1
                                Usage: 8790276
                                Duration: 2646876161
                                C2:
                                Flags/Description: ACPI IOPORT 0x414
                                Latency: 400
                                Usage: 10657198
                                Duration: 26728873313

                                 

                                  • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                    brauliobo

                                    same problem with kernel 4.16, will try now with 4.15. `cpupower frequency-info` output is a bit different with Pstate frequencies

                                     

                                    ~ uname -a
                                    Linux braulio-laptop 4.16.18-1-MANJARO #1 SMP PREEMPT Tue Jun 26 15:27:59 UTC 2018 x86_64 GNU/Linux

                                     

                                    ~/Downloads LANG=en sudo cpupower frequency-info
                                    analyzing CPU 0:
                                      driver: acpi-cpufreq
                                      CPUs which run at the same hardware frequency: 0
                                      CPUs which need to have their frequency coordinated by software: 0
                                      maximum transition latency:  Cannot determine or is not supported.
                                      hardware limits: 1.60 GHz - 2.00 GHz
                                      available frequency steps:  2.00 GHz, 1.70 GHz, 1.60 GHz
                                      available cpufreq governors: performance schedutil
                                      current policy: frequency should be within 1.60 GHz and 2.00 GHz.
                                                      The governor "schedutil" may decide which speed to use
                                                      within this range.
                                      current CPU frequency: 2.00 GHz (asserted by call to hardware)
                                      boost state support:
                                        Supported: no
                                        Active: no
                                        Boost States: 0
                                        Total States: 3
                                        Pstate-P0:  2000MHz
                                        Pstate-P1:  1700MHz
                                        Pstate-P2:  1600MHz

                                  • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                    brauliobo

                                    dmesg:

                                    [    0.000000] Linux version 4.18.0-1-custom+ (braulio@braulio-laptop) (gcc version 8.1.1 20180531 (GCC)) #6 SMP PREEMPT Wed Jul 4 18:16:01 -03 2018

                                    [    0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux-custom root=UUID=7bec7995-3557-480d-aee8-d9871405748d rw rcu_nocbs=0-15 pci=noaer idle=nomwait

                                    [    0.000000] KERNEL supported cpus:

                                    [    0.000000]   Intel GenuineIntel

                                    [    0.000000]   AMD AuthenticAMD

                                    [    0.000000]   Centaur CentaurHauls

                                    [    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'

                                    [    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'

                                    [    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'

                                    [    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256

                                    [    0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'compacted' format.

                                    [    0.000000] BIOS-provided physical RAM map:

                                    [    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d3ff] usable

                                    [    0.000000] BIOS-e820: [mem 0x000000000009d400-0x000000000009ffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000003ffffff] usable

                                    [    0.000000] BIOS-e820: [mem 0x0000000004000000-0x000000000400ffff] ACPI NVS

                                    [    0.000000] BIOS-e820: [mem 0x0000000004010000-0x0000000009e9ffff] usable

                                    [    0.000000] BIOS-e820: [mem 0x0000000009ea0000-0x0000000009ffffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x000000000a000000-0x00000000ccfaafff] usable

                                    [    0.000000] BIOS-e820: [mem 0x00000000ccfab000-0x00000000cd096fff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000cd097000-0x00000000cd0c6fff] ACPI data

                                    [    0.000000] BIOS-e820: [mem 0x00000000cd0c7000-0x00000000cd59efff] ACPI NVS

                                    [    0.000000] BIOS-e820: [mem 0x00000000cd59f000-0x00000000cdd4bfff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000cdd4c000-0x00000000ceffffff] usable

                                    [    0.000000] BIOS-e820: [mem 0x00000000cf000000-0x00000000dfffffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fd800000-0x00000000fd8fffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fe800000-0x00000000fe800fff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000feb80000-0x00000000fec01fff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fedc2000-0x00000000fedcffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fedd4000-0x00000000fedd5fff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000feefffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved

                                    [    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000051f33ffff] usable

                                    [    0.000000] NX (Execute Disable) protection: active

                                    [    0.000000] SMBIOS 3.0.0 present.

                                    [    0.000000] DMI: HP HP ENVY x360 Convertible 15m-bq1xx/83C6, BIOS F.17 03/29/2018

                                    [    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved

                                    [    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable

                                    [    0.000000] last_pfn = 0x51f340 max_arch_pfn = 0x400000000

                                    [    0.000000] MTRR default type: uncachable

                                    [    0.000000] MTRR fixed ranges enabled:

                                    [    0.000000]   00000-9FFFF write-back

                                    [    0.000000]   A0000-BFFFF write-through

                                    [    0.000000]   C0000-FFFFF write-protect

                                    [    0.000000] MTRR variable ranges enabled:

                                    [    0.000000]   0 base 000000000000 mask FFFF80000000 write-back

                                    [    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back

                                    [    0.000000]   2 base 0000C0000000 mask FFFFE0000000 write-back

                                    [    0.000000]   3 disabled

                                    [    0.000000]   4 disabled

                                    [    0.000000]   5 disabled

                                    [    0.000000]   6 disabled

                                    [    0.000000]   7 disabled

                                    [    0.000000] TOM2: 0000000520000000 aka 20992M

                                    [    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT 

                                    [    0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved

                                    [    0.000000] last_pfn = 0xcf000 max_arch_pfn = 0x400000000

                                    [    0.000000] Scanning 1 areas for low memory corruption

                                    [    0.000000] Base memory trampoline at [(____ptrval____)] 97000 size 24576

                                    [    0.000000] Using GB pages for direct mapping

                                    [    0.000000] BRK [0x35665f000, 0x35665ffff] PGTABLE

                                    [    0.000000] BRK [0x356660000, 0x356660fff] PGTABLE

                                    [    0.000000] BRK [0x356661000, 0x356661fff] PGTABLE

                                    [    0.000000] BRK [0x356662000, 0x356662fff] PGTABLE

                                    [    0.000000] BRK [0x356663000, 0x356663fff] PGTABLE

                                    [    0.000000] BRK [0x356664000, 0x356664fff] PGTABLE

                                    [    0.000000] BRK [0x356665000, 0x356665fff] PGTABLE

                                    [    0.000000] BRK [0x356666000, 0x356666fff] PGTABLE

                                    [    0.000000] BRK [0x356667000, 0x356667fff] PGTABLE

                                    [    0.000000] BRK [0x356668000, 0x356668fff] PGTABLE

                                    [    0.000000] BRK [0x356669000, 0x356669fff] PGTABLE

                                    [    0.000000] RAMDISK: [mem 0x35e41000-0x36f17fff]

                                    [    0.000000] ACPI: Early table checksum verification disabled

                                    [    0.000000] ACPI: RSDP 0x00000000000F05B0 000024 (v02 HPQOEM)

                                    [    0.000000] ACPI: XSDT 0x00000000CD0A7090 00009C (v01 HPQOEM SLIC-MPC 01072009 HP   00010013)

                                    [    0.000000] ACPI: FACP 0x00000000CD0BC1A0 000114 (v06 HPQOEM SLIC-MPC 01072009 HP   00010013)

                                    [    0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has valid Length but zero Address: 0x0000000000000000/0x1 (20180531/tbfadt-624)

                                    [    0.000000] ACPI: DSDT 0x00000000CD0A71B8 014FE2 (v02 HPQOEM 83C6     01072009 ACPI 20120913)

                                    [    0.000000] ACPI: FACS 0x00000000CD582F80 000040

                                    [    0.000000] ACPI: APIC 0x00000000CD0BC2B8 0000DE (v03 HPQOEM 83C6     01072009 HP   00010013)

                                    [    0.000000] ACPI: FPDT 0x00000000CD0BC398 000044 (v01 HPQOEM 83C6     01072009 HP   00010013)

                                    [    0.000000] ACPI: FIDT 0x00000000CD0BC3E0 00009C (v01 HPQOEM 83C6     01072009 HP   00010013)

                                    [    0.000000] ACPI: SSDT 0x00000000CD0BC480 0051C4 (v02 HPQOEM 83C6     00000002 ACPI 04000000)

                                    [    0.000000] ACPI: MCFG 0x00000000CD0C1648 00003C (v01 HPQOEM 83C6     01072009 HP   00010013)

                                    [    0.000000] ACPI: MSDM 0x00000000CD0C1688 000055 (v03 HPQOEM SLIC-MPC 00000001 HP   00010013)

                                    [    0.000000] ACPI: SSDT 0x00000000CD0C16E0 00119C (v01 HPQOEM 83C6     00000001 ACPI 00000001)

                                    [    0.000000] ACPI: CRAT 0x00000000CD0C2880 000838 (v01 HPQOEM 83C6     00000001 HP   00000001)

                                    [    0.000000] ACPI: CDIT 0x00000000CD0C30B8 000029 (v01 HPQOEM 83C6     00000001 HP   00000001)

                                    [    0.000000] ACPI: HPET 0x00000000CD0C30E8 000038 (v01 HPQOEM 83C6     01072009 HP   00000005)

                                    [    0.000000] ACPI: UEFI 0x00000000CD0C3120 000042 (v01 HPQOEM 83C6     00000000 HP   00000000)

                                    [    0.000000] ACPI: IVRS 0x00000000CD0C3168 0000D0 (v02 HPQOEM 83C6     00000001 HP   00000000)

                                    [    0.000000] ACPI: SSDT 0x00000000CD0C3238 001676 (v01 HPQOEM 83C6     00000001 ACPI 20120913)

                                    [    0.000000] ACPI: SSDT 0x00000000CD0C48B0 0018E2 (v01 HPQOEM 83C6     00000001 ACPI 20120913)

                                    [    0.000000] ACPI: Local APIC address 0xfee00000

                                    [    0.000000] No NUMA configuration found

                                    [    0.000000] Faking a node at [mem 0x0000000000000000-0x000000051f33ffff]

                                    [    0.000000] NODE_DATA(0) allocated [mem 0x51f33d000-0x51f33ffff]

                                    [    0.000000] tsc: Fast TSC calibration using PIT

                                    [    0.000000] Zone ranges:

                                    [    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]

                                    [    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]

                                    [    0.000000]   Normal   [mem 0x0000000100000000-0x000000051f33ffff]

                                    [    0.000000]   Device   empty

                                    [    0.000000] Movable zone start for each node

                                    [    0.000000] Early memory node ranges

                                    [    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009cfff]

                                    [    0.000000]   node   0: [mem 0x0000000000100000-0x0000000003ffffff]

                                    [    0.000000]   node   0: [mem 0x0000000004010000-0x0000000009e9ffff]

                                    [    0.000000]   node   0: [mem 0x000000000a000000-0x00000000ccfaafff]

                                    [    0.000000]   node   0: [mem 0x00000000cdd4c000-0x00000000ceffffff]

                                    [    0.000000]   node   0: [mem 0x0000000100000000-0x000000051f33ffff]

                                    [    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000051f33ffff]

                                    [    0.000000] On node 0 totalpages: 5166027

                                    [    0.000000]   DMA zone: 64 pages used for memmap

                                    [    0.000000]   DMA zone: 21 pages reserved

                                    [    0.000000]   DMA zone: 3996 pages, LIFO batch:0

                                    [    0.000000]   DMA32 zone: 13124 pages used for memmap

                                    [    0.000000]   DMA32 zone: 839919 pages, LIFO batch:31

                                    [    0.000000]   Normal zone: 67533 pages used for memmap

                                    [    0.000000]   Normal zone: 4322112 pages, LIFO batch:31

                                    [    0.000000] Reserved but unavailable: 100 pages

                                    [    0.000000] ACPI: PM-Timer IO Port: 0x808

                                    [    0.000000] ACPI: Local APIC address 0xfee00000

                                    [    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])

                                    [    0.000000] IOAPIC[0]: apic_id 9, version 33, address 0xfec00000, GSI 0-23

                                    [    0.000000] IOAPIC[1]: apic_id 10, version 33, address 0xfec01000, GSI 24-55

                                    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)

                                    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)

                                    [    0.000000] ACPI: IRQ0 used by override.

                                    [    0.000000] ACPI: IRQ9 used by override.

                                    [    0.000000] Using ACPI (MADT) for SMP configuration information

                                    [    0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000

                                    [    0.000000] smpboot: Allowing 16 CPUs, 8 hotplug CPUs

                                    [    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0x04000000-0x0400ffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0x09ea0000-0x09ffffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xccfab000-0xcd096fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xcd097000-0xcd0c6fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xcd0c7000-0xcd59efff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xcd59f000-0xcdd4bfff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xcf000000-0xdfffffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xf7ffffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfd7fffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfd800000-0xfd8fffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfd900000-0xfe7fffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfe800000-0xfe800fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfe801000-0xfeb7ffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfeb80000-0xfec01fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfecfffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xfedc1fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfedc2000-0xfedcffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfedd0000-0xfedd3fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfedd4000-0xfedd5fff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfedd6000-0xfedfffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfeefffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xfef00000-0xfeffffff]

                                    [    0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]

                                    [    0.000000] [mem 0xe0000000-0xf7ffffff] available for PCI devices

                                    [    0.000000] Booting paravirtualized kernel on bare hardware

                                    [    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns

                                    [    0.000000] random: get_random_bytes called from start_kernel+0x95/0x535 with crng_init=0

                                    [    0.000000] setup_percpu: NR_CPUS:320 nr_cpumask_bits:320 nr_cpu_ids:16 nr_node_ids:1

                                    [    0.000000] percpu: Embedded 46 pages/cpu @(____ptrval____) s151552 r8192 d28672 u262144

                                    [    0.000000] pcpu-alloc: s151552 r8192 d28672 u262144 alloc=1*2097152

                                    [    0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 12 13 14 15

                                    [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 5085285

                                    [    0.000000] Policy zone: Normal

                                    [    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux-custom root=UUID=7bec7995-3557-480d-aee8-d9871405748d rw rcu_nocbs=0-15 pci=noaer idle=nomwait

                                    [    0.000000] Calgary: detecting Calgary via BIOS EBDA area

                                    [    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!

                                    [    0.000000] Memory: 20231268K/20664108K available (10252K kernel code, 1289K rwdata, 3392K rodata, 1464K init, 600K bss, 432840K reserved, 0K cma-reserved)

                                    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1

                                    [    0.000000] ftrace: allocating 32792 entries in 129 pages

                                    [    0.000000] Preemptible hierarchical RCU implementation.

                                    [    0.000000] CONFIG_RCU_FANOUT set to non-default value of 32

                                    [    0.000000] RCU dyntick-idle grace-period acceleration is enabled.

                                    [    0.000000] RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=16.

                                    [    0.000000] RCU priority boosting: priority 1 delay 500 ms.

                                    [    0.000000] Tasks RCU enabled.

                                    [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16

                                    [    0.000000] NR_IRQS: 20736, nr_irqs: 1096, preallocated irqs: 16

                                    [    0.000000] Offload RCU callbacks from CPUs: 0-15.

                                    [    0.000000] spurious 8259A interrupt: IRQ7.

                                    [    0.000000] Console: colour dummy device 80x25

                                    [    0.000000] console [tty0] enabled

                                    [    0.000000] ACPI: Core revision 20180531

                                    [    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns

                                    [    0.000000] hpet clockevent registered

                                    [    0.000000] APIC: Switch to symmetric I/O mode setup

                                    [    0.002000] Switched APIC routing to physical flat.

                                    [    0.003000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1

                                    [    0.008000] tsc: Fast TSC calibration using PIT

                                    [    0.009000] tsc: Detected 1996.325 MHz processor

                                    [    0.009000] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x398d3dc8ad8, max_idle_ns: 881590722809 ns

                                    [    0.009000] Calibrating delay loop (skipped), value calculated using timer frequency.. 3992.65 BogoMIPS (lpj=1996325)

                                    [    0.009000] pid_max: default: 32768 minimum: 301

                                    [    0.009000] Security Framework initialized

                                    [    0.009000] Yama: becoming mindful.

                                    [    0.015890] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes)

                                    [    0.019179] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes)

                                    [    0.019360] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes)

                                    [    0.019468] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes)

                                    [    0.020074] CPU: Physical Processor ID: 0

                                    [    0.020075] CPU: Processor Core ID: 0

                                    [    0.020183] mce: CPU supports 23 MCE banks

                                    [    0.020206] LVT offset 1 assigned for vector 0xf9

                                    [    0.020272] LVT offset 2 assigned for vector 0xf4

                                    [    0.020287] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 512

                                    [    0.020288] Last level dTLB entries: 4KB 1536, 2MB 1536, 4MB 768, 1GB 0

                                    [    0.020290] Spectre V2 : Mitigation: Full AMD retpoline

                                    [    0.020291] Spectre V2 : Spectre v2 mitigation: Enabling Indirect Branch Prediction Barrier

                                    [    0.020292] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp

                                    [    0.029620] Freeing SMP alternatives memory: 28K

                                    [    0.032000] smpboot: CPU0: AMD Ryzen 5 2500U with Radeon Vega Mobile Gfx (family: 0x17, model: 0x11, stepping: 0x0)

                                    [    0.037017] Performance Events: Fam17h core perfctr, AMD PMU driver.

                                    [    0.037024] ... version:                0

                                    [    0.037025] ... bit width:              48

                                    [    0.037026] ... generic registers:      6

                                    [    0.037027] ... value mask:             0000ffffffffffff

                                    [    0.037028] ... max period:             00007fffffffffff

                                    [    0.037029] ... fixed-purpose events:   0

                                    [    0.037029] ... event mask:             000000000000003f

                                    [    0.038014] Hierarchical SRCU implementation.

                                    [    0.043421] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.

                                    [    0.044013] smp: Bringing up secondary CPUs ...

                                    [    0.051142] x86: Booting SMP configuration:

                                    [    0.051144] .... node  #0, CPUs:        #1  #2  #3  #4  #5  #6  #7

                                    [    0.100040] smp: Brought up 1 node, 8 CPUs

                                    [    0.100040] smpboot: Max logical packages: 2

                                    [    0.100040] smpboot: Total of 8 processors activated (31941.20 BogoMIPS)

                                    [    0.102223] devtmpfs: initialized

                                    [    0.102223] x86/mm: Memory block size: 128MB

                                    [    0.105403] PM: Registering ACPI NVS region [mem 0x04000000-0x0400ffff] (65536 bytes)

                                    [    0.105403] PM: Registering ACPI NVS region [mem 0xcd0c7000-0xcd59efff] (5079040 bytes)

                                    [    0.105403] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns

                                    [    0.105403] futex hash table entries: 4096 (order: 6, 262144 bytes)

                                    [    0.106227] pinctrl core: initialized pinctrl subsystem

                                    [    0.106386] RTC time: 11:36:20, date: 07/06/18

                                    [    0.106942] NET: Registered protocol family 16

                                    [    0.107192] cpuidle: using governor ladder

                                    [    0.109018] cpuidle: using governor menu

                                    [    0.110095] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it

                                    [    0.110098] ACPI: bus type PCI registered

                                    [    0.110099] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5

                                    [    0.110330] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)

                                    [    0.110334] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820

                                    [    0.110344] PCI: Using configuration type 1 for base access

                                    [    0.110702] mtrr: your CPUs had inconsistent variable MTRR settings

                                    [    0.110703] mtrr: probably your BIOS does not setup all CPUs.

                                    [    0.110703] mtrr: corrected configuration.

                                    [    0.113018] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages

                                    [    0.113020] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages

                                    [    0.114005] ACPI: Added _OSI(Module Device)

                                    [    0.114005] ACPI: Added _OSI(Processor Device)

                                    [    0.114005] ACPI: Added _OSI(3.0 _SCP Extensions)

                                    [    0.114005] ACPI: Added _OSI(Processor Aggregator Device)

                                    [    0.114005] ACPI: Added _OSI(Linux-Dell-Video)

                                    [    0.115821] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored

                                    [    0.137234] ACPI: 5 ACPI AML tables successfully acquired and loaded

                                    [    0.150263] ACPI: EC: EC started

                                    [    0.150265] ACPI: EC: interrupt blocked

                                    [    0.181649] ACPI: \_SB_.PCI0.SBRG.EC0_: Used as first EC

                                    [    0.181652] ACPI: \_SB_.PCI0.SBRG.EC0_: GPE=0x3, EC_CMD/EC_SC=0x66, EC_DATA=0x62

                                    [    0.181654] ACPI: \_SB_.PCI0.SBRG.EC0_: Used as boot DSDT EC to handle transactions

                                    [    0.181655] ACPI: Interpreter enabled

                                    [    0.181678] ACPI: (supports S0 S3 S4 S5)

                                    [    0.181680] ACPI: Using IOAPIC for interrupt routing

                                    [    0.182088] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug

                                    [    0.182531] ACPI: Enabled 2 GPEs in block 00 to 1F

                                    [    0.188180] ACPI: Power Resource [P0ST] (on)

                                    [    0.188235] ACPI: Power Resource [P3ST] (on)

                                    [    0.195304] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])

                                    [    0.195312] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]

                                    [    0.195611] acpi PNP0A08:00: _OSC: platform does not support [LTR]

                                    [    0.195900] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME PCIeCapability]

                                    [    0.195902] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration

                                    [    0.195922] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge

                                    [    0.196501] PCI host bridge to bus 0000:00

                                    [    0.196504] pci_bus 0000:00: root bus resource [io  0x0000-0x03af window]

                                    [    0.196506] pci_bus 0000:00: root bus resource [io  0x03e0-0x0cf7 window]

                                    [    0.196508] pci_bus 0000:00: root bus resource [io  0x03b0-0x03df window]

                                    [    0.196510] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]

                                    [    0.196511] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]

                                    [    0.196513] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]

                                    [    0.196515] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfebfffff window]

                                    [    0.196517] pci_bus 0000:00: root bus resource [mem 0xfee00000-0xffffffff window]

                                    [    0.196519] pci_bus 0000:00: root bus resource [bus 00-ff]

                                    [    0.196531] pci 0000:00:00.0: [1022:15d0] type 00 class 0x060000

                                    [    0.196703] pci 0000:00:00.2: [1022:15d1] type 00 class 0x080600

                                    [    0.196905] pci 0000:00:01.0: [1022:1452] type 00 class 0x060000

                                    [    0.197076] pci 0000:00:01.6: [1022:15d3] type 01 class 0x060400

                                    [    0.197213] pci 0000:00:01.6: PME# supported from D0 D3hot D3cold

                                    [    0.197362] pci 0000:00:01.7: [1022:15d3] type 01 class 0x060400

                                    [    0.197497] pci 0000:00:01.7: PME# supported from D0 D3hot D3cold

                                    [    0.197664] pci 0000:00:08.0: [1022:1452] type 00 class 0x060000

                                    [    0.197815] pci 0000:00:08.1: [1022:15db] type 01 class 0x060400

                                    [    0.197873] pci 0000:00:08.1: enabling Extended Tags

                                    [    0.197930] pci 0000:00:08.1: PME# supported from D0 D3hot D3cold

                                    [    0.198051] pci 0000:00:08.2: [1022:15dc] type 01 class 0x060400

                                    [    0.198108] pci 0000:00:08.2: enabling Extended Tags

                                    [    0.198165] pci 0000:00:08.2: PME# supported from D0 D3hot D3cold

                                    [    0.198333] pci 0000:00:14.0: [1022:790b] type 00 class 0x0c0500

                                    [    0.198569] pci 0000:00:14.3: [1022:790e] type 00 class 0x060100

                                    [    0.198830] pci 0000:00:18.0: [1022:15e8] type 00 class 0x060000

                                    [    0.198916] pci 0000:00:18.1: [1022:15e9] type 00 class 0x060000

                                    [    0.199005] pci 0000:00:18.2: [1022:15ea] type 00 class 0x060000

                                    [    0.199091] pci 0000:00:18.3: [1022:15eb] type 00 class 0x060000

                                    [    0.199183] pci 0000:00:18.4: [1022:15ec] type 00 class 0x060000

                                    [    0.199267] pci 0000:00:18.5: [1022:15ed] type 00 class 0x060000

                                    [    0.199360] pci 0000:00:18.6: [1022:15ee] type 00 class 0x060000

                                    [    0.199444] pci 0000:00:18.7: [1022:15ef] type 00 class 0x060000

                                    [    0.199676] pci 0000:01:00.0: [10ec:522a] type 00 class 0xff0000

                                    [    0.199719] pci 0000:01:00.0: reg 0x10: [mem 0xfe300000-0xfe300fff]

                                    [    0.199903] pci 0000:01:00.0: supports D1 D2

                                    [    0.199905] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold

                                    [    0.200175] pci 0000:00:01.6: PCI bridge to [bus 01]

                                    [    0.200185] pci 0000:00:01.6:   bridge window [mem 0xfe300000-0xfe3fffff]

                                    [    0.200329] pci 0000:02:00.0: [10ec:b822] type 00 class 0x028000

                                    [    0.200379] pci 0000:02:00.0: reg 0x10: [io  0xf000-0xf0ff]

                                    [    0.200424] pci 0000:02:00.0: reg 0x18: [mem 0xfe200000-0xfe20ffff 64bit]

                                    [    0.200635] pci 0000:02:00.0: supports D1 D2

                                    [    0.200637] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold

                                    [    0.200963] pci 0000:00:01.7: PCI bridge to [bus 02]

                                    [    0.200971] pci 0000:00:01.7:   bridge window [io  0xf000-0xffff]

                                    [    0.200975] pci 0000:00:01.7:   bridge window [mem 0xfe200000-0xfe2fffff]

                                    [    0.201139] pci 0000:03:00.0: [1002:15dd] type 00 class 0x030000

                                    [    0.201188] pci 0000:03:00.0: reg 0x10: [mem 0xe0000000-0xefffffff 64bit pref]

                                    [    0.201209] pci 0000:03:00.0: reg 0x18: [mem 0xf0000000-0xf01fffff 64bit pref]

                                    [    0.201223] pci 0000:03:00.0: reg 0x20: [io  0xe000-0xe0ff]

                                    [    0.201236] pci 0000:03:00.0: reg 0x24: [mem 0xfe000000-0xfe07ffff]

                                    [    0.201259] pci 0000:03:00.0: enabling Extended Tags

                                    [    0.201367] pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold

                                    [    0.201521] pci 0000:03:00.1: [1002:15de] type 00 class 0x040300

                                    [    0.201553] pci 0000:03:00.1: reg 0x10: [mem 0xfe088000-0xfe08bfff]

                                    [    0.201634] pci 0000:03:00.1: enabling Extended Tags

                                    [    0.201708] pci 0000:03:00.1: PME# supported from D1 D2 D3hot D3cold

                                    [    0.201818] pci 0000:03:00.2: [1022:15df] type 00 class 0x108000

                                    [    0.201874] pci 0000:03:00.2: reg 0x18: [mem 0xfdf00000-0xfdffffff]

                                    [    0.201909] pci 0000:03:00.2: reg 0x24: [mem 0xfe08c000-0xfe08dfff]

                                    [    0.201932] pci 0000:03:00.2: enabling Extended Tags

                                    [    0.202110] pci 0000:03:00.3: [1022:15e0] type 00 class 0x0c0330

                                    [    0.202149] pci 0000:03:00.3: reg 0x10: [mem 0xfde00000-0xfdefffff 64bit]

                                    [    0.202217] pci 0000:03:00.3: enabling Extended Tags

                                    [    0.202299] pci 0000:03:00.3: PME# supported from D0 D3hot D3cold

                                    [    0.202428] pci 0000:03:00.4: [1022:15e1] type 00 class 0x0c0330

                                    [    0.202467] pci 0000:03:00.4: reg 0x10: [mem 0xfdd00000-0xfddfffff 64bit]

                                    [    0.202535] pci 0000:03:00.4: enabling Extended Tags

                                    [    0.202617] pci 0000:03:00.4: PME# supported from D0 D3hot D3cold

                                    [    0.202723] pci 0000:03:00.6: [1022:15e3] type 00 class 0x040300

                                    [    0.202756] pci 0000:03:00.6: reg 0x10: [mem 0xfe080000-0xfe087fff]

                                    [    0.202835] pci 0000:03:00.6: enabling Extended Tags

                                    [    0.202909] pci 0000:03:00.6: PME# supported from D0 D3hot D3cold

                                    [    0.203062] pci 0000:00:08.1: PCI bridge to [bus 03]

                                    [    0.203069] pci 0000:00:08.1:   bridge window [io  0xe000-0xefff]

                                    [    0.203073] pci 0000:00:08.1:   bridge window [mem 0xfdd00000-0xfe0fffff]

                                    [    0.203079] pci 0000:00:08.1:   bridge window [mem 0xe0000000-0xf01fffff 64bit pref]

                                    [    0.203190] pci 0000:04:00.0: [1022:7901] type 00 class 0x010601

                                    [    0.203281] pci 0000:04:00.0: reg 0x24: [mem 0xfe100000-0xfe1007ff]

                                    [    0.203304] pci 0000:04:00.0: enabling Extended Tags

                                    [    0.203386] pci 0000:04:00.0: PME# supported from D3hot D3cold

                                    [    0.203508] pci 0000:00:08.2: PCI bridge to [bus 04]

                                    [    0.203518] pci 0000:00:08.2:   bridge window [mem 0xfe100000-0xfe1fffff]

                                    [    0.203982] ACPI: IRQ 7 override to edge, high

                                    [    0.204157] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11 14 15) *0

                                    [    0.204263] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 11 14 15) *0

                                    [    0.204361] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 11 14 15) *0

                                    [    0.204477] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 11 14 15) *0

                                    [    0.204574] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0

                                    [    0.204658] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0

                                    [    0.204741] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0

                                    [    0.204823] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0

                                    [    0.206025] ACPI: EC: interrupt unblocked

                                    [    0.206056] ACPI: EC: event unblocked

                                    [    0.206082] ACPI: \_SB_.PCI0.SBRG.EC0_: GPE=0x3, EC_CMD/EC_SC=0x66, EC_DATA=0x62

                                    [    0.206084] ACPI: \_SB_.PCI0.SBRG.EC0_: Used as boot DSDT EC to handle transactions and events

                                    [    0.207024] pci 0000:03:00.0: vgaarb: setting as boot VGA device

                                    [    0.207027] pci 0000:03:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none

                                    [    0.207030] pci 0000:03:00.0: vgaarb: bridge control possible

                                    [    0.207031] vgaarb: loaded

                                    [    0.209017] EDAC MC: Ver: 3.0.0

                                    [    0.210045] PCI: Using ACPI for IRQ routing

                                    [    0.213280] PCI: pci_cache_line_size set to 64 bytes

                                    [    0.213502] Expanded resource Reserved due to conflict with PCI Bus 0000:00

                                    [    0.213505] e820: reserve RAM buffer [mem 0x0009d400-0x0009ffff]

                                    [    0.213506] e820: reserve RAM buffer [mem 0x09ea0000-0x0bffffff]

                                    [    0.213508] e820: reserve RAM buffer [mem 0xccfab000-0xcfffffff]

                                    [    0.213509] e820: reserve RAM buffer [mem 0xcf000000-0xcfffffff]

                                    [    0.213510] e820: reserve RAM buffer [mem 0x51f340000-0x51fffffff]

                                    [    0.214005] NetLabel: Initializing

                                    [    0.214005] NetLabel:  domain hash size = 128

                                    [    0.214005] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO

                                    [    0.214005] NetLabel:  unlabeled traffic allowed by default

                                    [    0.214073] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0

                                    [    0.214079] hpet0: 3 comparators, 32-bit 14.318180 MHz counter

                                    [    0.216050] clocksource: Switched to clocksource tsc-early

                                    [    0.233797] VFS: Disk quotas dquot_6.6.0

                                    [    0.233851] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)

                                    [    0.233992] pnp: PnP ACPI init

                                    [    0.234230] system 00:00: [mem 0xf8000000-0xfbffffff] has been reserved

                                    [    0.234237] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)

                                    [    0.234358] system 00:01: [mem 0xfeb80000-0xfebfffff] could not be reserved

                                    [    0.234363] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)

                                    [    0.234535] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)

                                    [    0.234641] pnp 00:03: Plug and Play ACPI device, IDs HPQ8001 PNP0303 (active)

                                    [    0.234677] pnp 00:04: Plug and Play ACPI device, IDs SYN324e ETD0000 PNP0f13 (active)

                                    [    0.235048] system 00:05: [io  0x04d0-0x04d1] has been reserved

                                    [    0.235050] system 00:05: [io  0x040b] has been reserved

                                    [    0.235052] system 00:05: [io  0x04d6] has been reserved

                                    [    0.235054] system 00:05: [io  0x0c00-0x0c01] has been reserved

                                    [    0.235056] system 00:05: [io  0x0c14] has been reserved

                                    [    0.235058] system 00:05: [io  0x0c50-0x0c51] has been reserved

                                    [    0.235068] system 00:05: [io  0x0c52] has been reserved

                                    [    0.235070] system 00:05: [io  0x0c6c] has been reserved

                                    [    0.235071] system 00:05: [io  0x0c6f] has been reserved

                                    [    0.235073] system 00:05: [io  0x0cd0-0x0cd1] has been reserved

                                    [    0.235075] system 00:05: [io  0x0cd2-0x0cd3] has been reserved

                                    [    0.235077] system 00:05: [io  0x0cd4-0x0cd5] has been reserved

                                    [    0.235079] system 00:05: [io  0x0cd6-0x0cd7] has been reserved

                                    [    0.235080] system 00:05: [io  0x0cd8-0x0cdf] has been reserved

                                    [    0.235082] system 00:05: [io  0x0800-0x089f] has been reserved

                                    [    0.235084] system 00:05: [io  0x0b00-0x0b0f] has been reserved

                                    [    0.235086] system 00:05: [io  0x0b20-0x0b3f] has been reserved

                                    [    0.235087] system 00:05: [io  0x0900-0x090f] has been reserved

                                    [    0.235089] system 00:05: [io  0x0910-0x091f] has been reserved

                                    [    0.235092] system 00:05: [mem 0xfec00000-0xfec00fff] could not be reserved

                                    [    0.235094] system 00:05: [mem 0xfec01000-0xfec01fff] could not be reserved

                                    [    0.235096] system 00:05: [mem 0xfedc0000-0xfedc0fff] has been reserved

                                    [    0.235098] system 00:05: [mem 0xfee00000-0xfee00fff] has been reserved

                                    [    0.235100] system 00:05: [mem 0xfed80000-0xfed8ffff] could not be reserved

                                    [    0.235102] system 00:05: [mem 0xfec10000-0xfec10fff] has been reserved

                                    [    0.235104] system 00:05: [mem 0xff000000-0xffffffff] has been reserved

                                    [    0.235109] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)

                                    [    0.235845] pnp: PnP ACPI: found 6 devices

                                    [    0.246996] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns

                                    [    0.247015] pci 0000:00:01.6: bridge window [io  0x1000-0x0fff] to [bus 01] add_size 1000

                                    [    0.247019] pci 0000:00:01.6: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000

                                    [    0.247055] pci 0000:00:01.6: BAR 15: assigned [mem 0xf0200000-0xf03fffff 64bit pref]

                                    [    0.247060] pci 0000:00:01.6: BAR 13: assigned [io  0x1000-0x1fff]

                                    [    0.247063] pci 0000:00:01.6: PCI bridge to [bus 01]

                                    [    0.247066] pci 0000:00:01.6:   bridge window [io  0x1000-0x1fff]

                                    [    0.247072] pci 0000:00:01.6:   bridge window [mem 0xfe300000-0xfe3fffff]

                                    [    0.247076] pci 0000:00:01.6:   bridge window [mem 0xf0200000-0xf03fffff 64bit pref]

                                    [    0.247084] pci 0000:00:01.7: PCI bridge to [bus 02]

                                    [    0.247087] pci 0000:00:01.7:   bridge window [io  0xf000-0xffff]

                                    [    0.247093] pci 0000:00:01.7:   bridge window [mem 0xfe200000-0xfe2fffff]

                                    [    0.247104] pci 0000:00:08.1: PCI bridge to [bus 03]

                                    [    0.247107] pci 0000:00:08.1:   bridge window [io  0xe000-0xefff]

                                    [    0.247113] pci 0000:00:08.1:   bridge window [mem 0xfdd00000-0xfe0fffff]

                                    [    0.247117] pci 0000:00:08.1:   bridge window [mem 0xe0000000-0xf01fffff 64bit pref]

                                    [    0.247124] pci 0000:00:08.2: PCI bridge to [bus 04]

                                    [    0.247130] pci 0000:00:08.2:   bridge window [mem 0xfe100000-0xfe1fffff]

                                    [    0.247142] pci_bus 0000:00: resource 4 [io  0x0000-0x03af window]

                                    [    0.247143] pci_bus 0000:00: resource 5 [io  0x03e0-0x0cf7 window]

                                    [    0.247145] pci_bus 0000:00: resource 6 [io  0x03b0-0x03df window]

                                    [    0.247147] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff window]

                                    [    0.247148] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]

                                    [    0.247150] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]

                                    [    0.247152] pci_bus 0000:00: resource 10 [mem 0xe0000000-0xfebfffff window]

                                    [    0.247153] pci_bus 0000:00: resource 11 [mem 0xfee00000-0xffffffff window]

                                    [    0.247155] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]

                                    [    0.247157] pci_bus 0000:01: resource 1 [mem 0xfe300000-0xfe3fffff]

                                    [    0.247158] pci_bus 0000:01: resource 2 [mem 0xf0200000-0xf03fffff 64bit pref]

                                    [    0.247160] pci_bus 0000:02: resource 0 [io  0xf000-0xffff]

                                    [    0.247161] pci_bus 0000:02: resource 1 [mem 0xfe200000-0xfe2fffff]

                                    [    0.247163] pci_bus 0000:03: resource 0 [io  0xe000-0xefff]

                                    [    0.247165] pci_bus 0000:03: resource 1 [mem 0xfdd00000-0xfe0fffff]

                                    [    0.247166] pci_bus 0000:03: resource 2 [mem 0xe0000000-0xf01fffff 64bit pref]

                                    [    0.247168] pci_bus 0000:04: resource 1 [mem 0xfe100000-0xfe1fffff]

                                    [    0.247423] NET: Registered protocol family 2

                                    [    0.247773] tcp_listen_portaddr_hash hash table entries: 16384 (order: 6, 262144 bytes)

                                    [    0.247888] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)

                                    [    0.248343] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)

                                    [    0.248497] TCP: Hash tables configured (established 262144 bind 65536)

                                    [    0.248578] UDP hash table entries: 16384 (order: 7, 524288 bytes)

                                    [    0.248680] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes)

                                    [    0.248862] NET: Registered protocol family 1

                                    [    0.249024] pci 0000:03:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]

                                    [    0.249032] pci 0000:03:00.1: Linked as a consumer to 0000:03:00.0

                                    [    0.249521] PCI: CLS 64 bytes, default 64

                                    [    0.249576] Unpacking initramfs...

                                    [    0.611822] Freeing initrd memory: 17244K

                                    [    0.611853] AMD-Vi: Unable to write to IOMMU perf counter.

                                    [    0.612008] pci 0000:00:00.2: can't derive routing for PCI INT A

                                    [    0.612010] pci 0000:00:00.2: PCI INT A: not connected

                                    [    0.612514] iommu: Adding device 0000:00:01.0 to group 0

                                    [    0.612758] iommu: Adding device 0000:00:01.6 to group 1

                                    [    0.612988] iommu: Adding device 0000:00:01.7 to group 2

                                    [    0.613252] iommu: Adding device 0000:00:08.0 to group 3

                                    [    0.613287] iommu: Adding device 0000:00:08.1 to group 3

                                    [    0.613319] iommu: Adding device 0000:00:08.2 to group 3

                                    [    0.613534] iommu: Adding device 0000:00:14.0 to group 4

                                    [    0.613566] iommu: Adding device 0000:00:14.3 to group 4

                                    [    0.613821] iommu: Adding device 0000:00:18.0 to group 5

                                    [    0.613869] iommu: Adding device 0000:00:18.1 to group 5

                                    [    0.613901] iommu: Adding device 0000:00:18.2 to group 5

                                    [    0.613934] iommu: Adding device 0000:00:18.3 to group 5

                                    [    0.613965] iommu: Adding device 0000:00:18.4 to group 5

                                    [    0.613999] iommu: Adding device 0000:00:18.5 to group 5

                                    [    0.614030] iommu: Adding device 0000:00:18.6 to group 5

                                    [    0.614062] iommu: Adding device 0000:00:18.7 to group 5

                                    [    0.614346] iommu: Adding device 0000:01:00.0 to group 6

                                    [    0.614638] iommu: Adding device 0000:02:00.0 to group 7

                                    [    0.614734] iommu: Adding device 0000:03:00.0 to group 3

                                    [    0.614803] iommu: Adding device 0000:03:00.1 to group 3

                                    [    0.614874] iommu: Adding device 0000:03:00.2 to group 3

                                    [    0.614943] iommu: Adding device 0000:03:00.3 to group 3

                                    [    0.615012] iommu: Adding device 0000:03:00.4 to group 3

                                    [    0.615092] iommu: Adding device 0000:03:00.6 to group 3

                                    [    0.615163] iommu: Adding device 0000:04:00.0 to group 3

                                    [    0.615501] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40

                                    [    0.615502] AMD-Vi: Extended features (0xf77ef22294ada):

                                    [    0.615503]  PPR NX GT IA GA PC GA_vAPIC

                                    [    0.615507] AMD-Vi: Interrupt remapping enabled

                                    [    0.615507] AMD-Vi: virtual APIC enabled

                                    [    0.711197] AMD-Vi: Lazy IO/TLB flushing enabled

                                    [    0.712719] amd_uncore: AMD NB counters detected

                                    [    0.712725] amd_uncore: AMD LLC counters detected

                                    [    0.713335] Scanning for low memory corruption every 60 seconds

                                    [    0.714392] Initialise system trusted keyrings

                                    [    0.714447] Key type blacklist registered

                                    [    0.714560] workingset: timestamp_bits=44 max_order=23 bucket_order=0

                                    [    0.716624] zbud: loaded

                                    [    0.716991] pstore: using deflate compression

                                    [    0.719173] Key type asymmetric registered

                                    [    0.719175] Asymmetric key parser 'x509' registered

                                    [    0.719242] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)

                                    [    0.719314] io scheduler noop registered

                                    [    0.719315] io scheduler deadline registered

                                    [    0.719427] io scheduler cfq registered (default)

                                    [    0.719428] io scheduler mq-deadline registered

                                    [    0.719429] io scheduler kyber registered

                                    [    0.719486] io scheduler bfq registered

                                    [    0.720494] pcieport 0000:00:01.6: Signaling PME with IRQ 26

                                    [    0.720528] pcieport 0000:00:01.7: Signaling PME with IRQ 27

                                    [    0.720572] pcieport 0000:00:08.1: Signaling PME with IRQ 28

                                    [    0.720617] pcieport 0000:00:08.2: Signaling PME with IRQ 29

                                    [    0.720640] pciehp 0000:00:01.6:pcie004: Slot #0 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise- Interlock- NoCompl+ LLActRep+

                                    [    0.720744] vesafb: mode is 1920x1080x32, linelength=7680, pages=0

                                    [    0.720745] vesafb: scrolling: redraw

                                    [    0.720747] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0

                                    [    0.720761] vesafb: framebuffer at 0xe0000000, mapped to 0x(____ptrval____), using 8128k, total 8128k

                                    [    0.812550] Console: switching to colour frame buffer device 240x67

                                    [    0.861379] fb0: VESA VGA frame buffer device

                                    [    0.861471] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0

                                    [    0.861480] ACPI: Power Button [PWRB]

                                    [    0.861549] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1

                                    [    0.861555] ACPI: Lid Switch [LID0]

                                    [    0.861602] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2

                                    [    0.861618] ACPI: Power Button [PWRF]

                                    [    0.861757] ACPI: Video Device [VGA2] (multi-head: yes  rom: no  post: no)

                                    [    0.862101] acpi device:16: registered as cooling_device0

                                    [    0.862152] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:15/LNXVIDEO:02/input/input3

                                    [    0.862202] Monitor-Mwait will be used to enter C-1 state

                                    [    0.868009] thermal LNXTHERM:00: registered as thermal_zone0

                                    [    0.868011] ACPI: Thermal Zone [TZS0] (54 C)

                                    [    0.868520] thermal LNXTHERM:01: registered as thermal_zone1

                                    [    0.868522] ACPI: Thermal Zone [TZS1] (48 C)

                                    [    0.868757] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

                                    [    0.871534] ledtrig-cpu: registered to indicate activity on CPUs

                                    [    0.872018] NET: Registered protocol family 10

                                    [    0.877343] Segment Routing with IPv6

                                    [    0.877374] NET: Registered protocol family 17

                                    [    0.878394] RAS: Correctable Errors collector initialized.

                                    [    0.879582] microcode: CPU0: patch_level=0x08101007

                                    [    0.879587] microcode: CPU1: patch_level=0x08101007

                                    [    0.879607] microcode: CPU2: patch_level=0x08101007

                                    [    0.879612] microcode: CPU3: patch_level=0x08101007

                                    [    0.879616] microcode: CPU4: patch_level=0x08101007

                                    [    0.879624] microcode: CPU5: patch_level=0x08101007

                                    [    0.879630] microcode: CPU6: patch_level=0x08101007

                                    [    0.879637] microcode: CPU7: patch_level=0x08101007

                                    [    0.879704] microcode: Microcode Update Driver: v2.2.

                                    [    0.879731] sched_clock: Marking stable (879698841, 0)->(1096451519, -216752678)

                                    [    0.880030] registered taskstats version 1

                                    [    0.880039] Loading compiled-in X.509 certificates

                                    [    0.880075] zswap: loaded using pool lzo/zbud

                                    [    0.884062] Key type big_key registered

                                    [    0.884752]   Magic number: 10:203:630

                                    [    0.884802] acpi PNP0C31:00: hash matches

                                    [    0.884854] hctosys: unable to open rtc device (rtc0)

                                    [    1.370776] Freeing unused kernel memory: 1464K

                                    [    1.370779] Write protecting the kernel read-only data: 16384k

                                    [    1.373911] Freeing unused kernel memory: 2016K

                                    [    1.376363] Freeing unused kernel memory: 704K

                                    [    1.477351] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12

                                    [    1.483111] serio: i8042 KBD port at 0x60,0x64 irq 1

                                    [    1.483201] serio: i8042 AUX port at 0x60,0x64 irq 12

                                    [    1.484000] cryptd: max_cpu_qlen set to 1000

                                    [    1.487685] ACPI: bus type USB registered

                                    [    1.487718] usbcore: registered new interface driver usbfs

                                    [    1.487731] usbcore: registered new interface driver hub

                                    [    1.487801] usbcore: registered new device driver usb

                                    [    1.491815] AVX2 version of gcm_enc/dec engaged.

                                    [    1.491817] AES CTR mode by8 optimization enabled

                                    [    1.492044] SCSI subsystem initialized

                                    [    1.496997] xhci_hcd 0000:03:00.3: xHCI Host Controller

                                    [    1.497024] xhci_hcd 0000:03:00.3: new USB bus registered, assigned bus number 1

                                    [    1.497211] xhci_hcd 0000:03:00.3: hcc params 0x0270ffe5 hci version 0x110 quirks 0x0000000040000410

                                    [    1.497911] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18

                                    [    1.497914] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

                                    [    1.497916] usb usb1: Product: xHCI Host Controller

                                    [    1.497919] usb usb1: Manufacturer: Linux 4.18.0-1-custom+ xhci-hcd

                                    [    1.497920] usb usb1: SerialNumber: 0000:03:00.3

                                    [    1.498164] hub 1-0:1.0: USB hub found

                                    [    1.498184] hub 1-0:1.0: 4 ports detected

                                    [    1.499479] xhci_hcd 0000:03:00.3: xHCI Host Controller

                                    [    1.499498] xhci_hcd 0000:03:00.3: new USB bus registered, assigned bus number 2

                                    [    1.499504] xhci_hcd 0000:03:00.3: Host supports USB 3.10 Enhanced SuperSpeed

                                    [    1.499541] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.

                                    [    1.499578] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.18

                                    [    1.499580] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

                                    [    1.499583] usb usb2: Product: xHCI Host Controller

                                    [    1.499585] usb usb2: Manufacturer: Linux 4.18.0-1-custom+ xhci-hcd

                                    [    1.499587] usb usb2: SerialNumber: 0000:03:00.3

                                    [    1.499804] hub 2-0:1.0: USB hub found

                                    [    1.499823] hub 2-0:1.0: 4 ports detected

                                    [    1.500059] libata version 3.00 loaded.

                                    [    1.502148] xhci_hcd 0000:03:00.4: xHCI Host Controller

                                    [    1.502155] xhci_hcd 0000:03:00.4: new USB bus registered, assigned bus number 3

                                    [    1.502311] xhci_hcd 0000:03:00.4: hcc params 0x0260ffe5 hci version 0x110 quirks 0x0000000040000410

                                    [    1.502982] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18

                                    [    1.502986] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1

                                    [    1.502988] usb usb3: Product: xHCI Host Controller

                                    [    1.502990] usb usb3: Manufacturer: Linux 4.18.0-1-custom+ xhci-hcd

                                    [    1.502992] usb usb3: SerialNumber: 0000:03:00.4

                                    [    1.503212] hub 3-0:1.0: USB hub found

                                    [    1.503233] hub 3-0:1.0: 2 ports detected

                                    [    1.503871] xhci_hcd 0000:03:00.4: xHCI Host Controller

                                    [    1.503876] xhci_hcd 0000:03:00.4: new USB bus registered, assigned bus number 4

                                    [    1.503882] xhci_hcd 0000:03:00.4: Host supports USB 3.10 Enhanced SuperSpeed

                                    [    1.503924] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.

                                    [    1.503955] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.18

                                    [    1.503957] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1

                                    [    1.503959] usb usb4: Product: xHCI Host Controller

                                    [    1.503961] usb usb4: Manufacturer: Linux 4.18.0-1-custom+ xhci-hcd

                                    [    1.503963] usb usb4: SerialNumber: 0000:03:00.4

                                    [    1.504170] hub 4-0:1.0: USB hub found

                                    [    1.504191] hub 4-0:1.0: 1 port detected

                                    [    1.504493] ahci 0000:04:00.0: version 3.0

                                    [    1.509421] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4

                                    [    1.514945] ahci 0000:04:00.0: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl SATA mode

                                    [    1.514950] ahci 0000:04:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part deso sadm sds

                                    [    1.514954] ahci 0000:04:00.0: both AHCI_HFLAG_MULTI_MSI flag set and custom irq handler implemented

                                    [    1.515951] scsi host0: ahci

                                    [    1.516328] scsi host1: ahci

                                    [    1.516408] ata1: SATA max UDMA/133 abar m2048@0xfe100000 port 0xfe100100 irq 51

                                    [    1.516411] ata2: SATA max UDMA/133 abar m2048@0xfe100000 port 0xfe100180 irq 52

                                    [    1.759737] tsc: Refined TSC clocksource calibration: 1996.240 MHz

                                    [    1.759756] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x398c9cdeefa, max_idle_ns: 881590591131 ns

                                    [    1.760163] clocksource: Switched to clocksource tsc

                                    [    1.826423] usb 1-4: new high-speed USB device number 2 using xhci_hcd

                                    [    1.826444] usb 3-2: new high-speed USB device number 2 using xhci_hcd

                                    [    1.957110] usb 3-2: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=88.32

                                    [    1.957114] usb 3-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0

                                    [    1.957116] usb 3-2: Product: USB2.0 Hub

                                    [    1.983748] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

                                    [    1.983791] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

                                    [    1.985050] ata1.00: ATA-9: WDC WDS240G2G0B-00EPW0, UJ190000, max UDMA/133

                                    [    1.985052] ata1.00: 468877312 sectors, multi 1: LBA48 NCQ (depth 32)

                                    [    1.985718] ata2.00: ATA-9: HGST HTS721010A9E630, JB0OA3T0, max UDMA/133

                                    [    1.985721] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA

                                    [    1.988453] ata2.00: configured for UDMA/133

                                    [    1.991407] ata1.00: configured for UDMA/133

                                    [    1.992262] scsi 0:0:0:0: Direct-Access     ATA      WDC WDS240G2G0B- 0000 PQ: 0 ANSI: 5

                                    [    1.993280] scsi 1:0:0:0: Direct-Access     ATA      HGST HTS721010A9 A3T0 PQ: 0 ANSI: 5

                                    [    1.995063] usb 1-4: New USB device found, idVendor=04f2, idProduct=b593, bcdDevice= 0.10

                                    [    1.995066] usb 1-4: New USB device strings: Mfr=3, Product=1, SerialNumber=2

                                    [    1.995068] usb 1-4: Product: HP Wide Vision FHD Camera

                                    [    1.995069] usb 1-4: Manufacturer: Chicony Electronics Co.,Ltd.

                                    [    1.995071] usb 1-4: SerialNumber: 1

                                    [    1.996192] sd 0:0:0:0: [sda] 468877312 512-byte logical blocks: (240 GB/224 GiB)

                                    [    1.996210] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)

                                    [    1.996213] sd 1:0:0:0: [sdb] 4096-byte physical blocks

                                    [    1.996226] sd 0:0:0:0: [sda] Write Protect is off

                                    [    1.996227] sd 1:0:0:0: [sdb] Write Protect is off

                                    [    1.996228] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

                                    [    1.996231] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00

                                    [    1.996251] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

                                    [    1.996268] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

                                    [    1.996885]  sda: sda1 sda2

                                    [    1.997287] sd 0:0:0:0: [sda] Attached SCSI disk

                                    [    2.016573] hub 3-2:1.0: USB hub found

                                    [    2.016995] hub 3-2:1.0: 4 ports detected

                                    [    2.281853]  sdb: sdb1 sdb2 sdb3 sdb4 sdb5

                                    [    2.283408] sd 1:0:0:0: [sdb] Attached SCSI disk

                                    [    2.307053] usb 3-2.3: new full-speed USB device number 3 using xhci_hcd

                                    [    2.309198] random: fast init done

                                    [    2.339011] raid6: sse2x1   gen()  4742 MB/s

                                    [    2.356004] raid6: sse2x1   xor()  4205 MB/s

                                    [    2.373004] raid6: sse2x2   gen()  8234 MB/s

                                    [    2.390026] raid6: sse2x2   xor()  5626 MB/s

                                    [    2.407005] raid6: sse2x4   gen()  9289 MB/s

                                    [    2.424006] raid6: sse2x4   xor()  5283 MB/s

                                    [    2.425982] usb 3-2.3: New USB device found, idVendor=0483, idProduct=91d1, bcdDevice= 1.11

                                    [    2.425985] usb 3-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3

                                    [    2.425988] usb 3-2.3: Product: ST_SENSOR_HUB

                                    [    2.425990] usb 3-2.3: Manufacturer: STMicroelectronics

                                    [    2.425992] usb 3-2.3: SerialNumber: ST_SENSOR_HUB

                                    [    2.441044] raid6: avx2x1   gen()  9984 MB/s

                                    [    2.458004] raid6: avx2x1   xor()  7589 MB/s

                                    [    2.468360] hidraw: raw HID events driver (C) Jiri Kosina

                                    [    2.475008] raid6: avx2x2   gen() 12492 MB/s

                                    [    2.482508] usbcore: registered new interface driver usbhid

                                    [    2.482509] usbhid: USB HID core driver

                                    [    2.485446] hid-generic 0003:0483:91D1.0001: hiddev0,hidraw0: USB HID v1.10 Device [STMicroelectronics ST_SENSOR_HUB] on usb-0000:03:00.4-2.3/input0

                                    [    2.492006] raid6: avx2x2   xor()  8066 MB/s

                                    [    2.509008] raid6: avx2x4   gen() 13195 MB/s

                                    [    2.526007] raid6: avx2x4   xor()  7638 MB/s

                                    [    2.526008] raid6: using algorithm avx2x4 gen() 13195 MB/s

                                    [    2.526009] raid6: .... xor() 7638 MB/s, rmw enabled

                                    [    2.526010] raid6: using avx2x2 recovery algorithm

                                    [    2.530115] xor: automatically using best checksumming function   avx      

                                    [    2.531029] usb 3-2.4: new full-speed USB device number 4 using xhci_hcd

                                    [    2.558812] Btrfs loaded, crc32c=crc32c-intel

                                    [    2.559623] BTRFS: device label root devid 1 transid 82694 /dev/sda2

                                    [    2.630005] usb 3-2.4: New USB device found, idVendor=0bda, idProduct=b00b, bcdDevice= 1.10

                                    [    2.630017] usb 3-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3

                                    [    2.630019] usb 3-2.4: Product: Bluetooth Radio

                                    [    2.630021] usb 3-2.4: Manufacturer: Realtek

                                    [    2.630022] usb 3-2.4: SerialNumber: 00e04c000001

                                    [    2.846602] device-mapper: uevent: version 1.0.3

                                    [    2.846746] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com

                                    [    2.884595] BTRFS info (device sda2): disk space caching is enabled

                                    [    2.884598] BTRFS info (device sda2): has skinny extents

                                    [    3.103869] BTRFS info (device sda2): enabling ssd optimizations

                                    [    3.375740] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN +PCRE2 default-hierarchy=hybrid)

                                    [    3.389586] systemd[1]: Detected architecture x86-64.

                                    [    3.403756] systemd[1]: Set hostname to <braulio-laptop>.

                                    [    3.547250] systemd[1]: /etc/systemd/system/rc-local.service:11: Support for option SysVStartPriority= has been removed and it is ignored

                                    [    3.552616] random: systemd: uninitialized urandom read (16 bytes read)

                                    [    3.555611] systemd[1]: Created slice system-systemd\x2dfsck.slice.

                                    [    3.556518] random: systemd: uninitialized urandom read (16 bytes read)

                                    [    3.556654] systemd[1]: Listening on Journal Socket (/dev/log).

                                    [    3.557457] random: systemd: uninitialized urandom read (16 bytes read)

                                    [    3.559690] systemd[1]: Listening on LVM2 metadata daemon socket.

                                    [    3.560541] systemd[1]: Reached target Login Prompts.

                                    [    3.561311] systemd[1]: Listening on udev Kernel Socket.

                                    [    3.562346] systemd[1]: Created slice User and Session Slice.

                                    [    3.637369] sd 0:0:0:0: Attached scsi generic sg0 type 0

                                    [    3.637448] sd 1:0:0:0: Attached scsi generic sg1 type 0

                                    [    3.692686] vboxdrv: loading out-of-tree module taints kernel.

                                    [    3.701658] vboxdrv: Found 8 processor cores

                                    [    3.717433] vboxdrv: TSC mode is Invariant, tentative frequency 1996130334 Hz

                                    [    3.717435] vboxdrv: Successfully loaded version 5.2.14 (interface 0x00290001)

                                    [    3.741698] VBoxPciLinuxInit

                                    [    3.741705] vboxpci: IOMMU found

                                    [    3.743649] VBoxNetAdp: Successfully started.

                                    [    3.746602] VBoxNetFlt: Successfully started.

                                    [    4.000725] BTRFS info (device sda2): use zstd compression, level 0

                                    [    4.000731] BTRFS info (device sda2): turning on discard

                                    [    4.000733] BTRFS info (device sda2): enabling auto defrag

                                    [    4.000736] BTRFS info (device sda2): using default commit interval 30s

                                    [    4.000739] BTRFS info (device sda2): disk space caching is enabled

                                    [    4.105703] systemd-journald[354]: Received request to flush runtime journal from PID 1

                                    [    5.192636] random: crng init done

                                    [    5.192640] random: 7 urandom warning(s) missed due to ratelimiting

                                    [    6.041336] acpi_cpufreq: overriding BIOS provided _PSD data

                                    [    6.067441] input: HP Wireless hotkeys as /devices/virtual/input/input6

                                    [    6.067767] amd_gpio AMDI0030:00: Failed to get gpio IRQ: -22

                                    [    6.094109] amd_gpio: probe of AMDI0030:00 failed with error -22

                                    [    6.094447] cmi: probe of SMB0001:00 failed with error -5

                                    [    6.095968] rtc_cmos 00:02: RTC can wake from S4

                                    [    6.096448] rtc_cmos 00:02: registered as rtc0

                                    [    6.096477] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs

                                    [    6.103927] acpi PNP0C14:01: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00)

                                    [    6.105319] ACPI: Battery Slot [BAT0] (battery present)

                                    [    6.109571] ACPI: AC Adapter [ADP1] (on-line)

                                    [    6.120422] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0

                                    [    6.120426] piix4_smbus 0000:00:14.0: Using register 0x02 for SMBus port selection

                                    [    6.126677] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver

                                    [    6.126839] sp5100-tco sp5100-tco: Using 0xfed80b00 for watchdog MMIO address

                                    [    6.126854] sp5100-tco sp5100-tco: Watchdog hardware is disabled

                                    [    6.174751] hp_accel: laptop model unknown, using default axes configuration

                                    [    6.198844] Linux agpgart interface v0.103

                                    [    6.199242] lis3lv02d: unknown sensor type 0x0

                                    [    6.246081] hp_accel: probe of HPQ6007:00 failed with error -22

                                    [    6.281819] cfg80211: Loading compiled-in X.509 certificates for regulatory database

                                    [    6.291853] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'

                                    [    6.293857] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2

                                    [    6.293862] cfg80211: failed to load regulatory.db

                                    [    6.350795] kvm: Nested Virtualization enabled

                                    [    6.350823] kvm: Nested Paging enabled

                                    [    6.350825] SVM: Virtual VMLOAD VMSAVE supported

                                    [    6.350825] SVM: Virtual GIF supported

                                    [    6.355284] ACPI Error: Field [D128] at bit offset/length 128/1024 exceeds size of target Buffer (160 bits) (20180531/dsopcode-201)

                                    [    6.384121] MCE: In-kernel MCE decoding enabled.

                                    [    6.387393] media: Linux media interface: v0.10

                                    [    6.389599] EDAC amd64: Node 0: DRAM ECC disabled.

                                    [    6.389603] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.

                                                    Either enable ECC checking or force module loading by setting 'ecc_enable_override'.

                                                    (Note that use of the override may cause unknown side effects.)

                                    [    6.399175] ACPI Error: Method parse/execution failed \HWMC, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.401360] ACPI Error: Method parse/execution failed \_SB.WMID.WMAA, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.401572] snd_hda_intel 0000:03:00.1: Handle vga_switcheroo audio client

                                    [    6.401629] ACPI Error: Field [D128] at bit offset/length 128/1024 exceeds size of target Buffer (160 bits) (20180531/dsopcode-201)

                                    [    6.401644] ACPI Error: Method parse/execution failed \HWMC, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.401658] ACPI Error: Method parse/execution failed \_SB.WMID.WMAA, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.401810] ACPI Error: Field [D128] at bit offset/length 128/1024 exceeds size of target Buffer (160 bits) (20180531/dsopcode-201)

                                    [    6.401821] ACPI Error: Method parse/execution failed \HWMC, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.401833] ACPI Error: Method parse/execution failed \_SB.WMID.WMAA, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.402793] input: HP WMI hotkeys as /devices/virtual/input/input8

                                    [    6.403568] ACPI Error: Field [D128] at bit offset/length 128/1024 exceeds size of target Buffer (160 bits) (20180531/dsopcode-201)

                                    [    6.403587] ACPI Error: Method parse/execution failed \HWMC, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.403604] ACPI Error: Method parse/execution failed \_SB.WMID.WMAA, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.403739] ACPI Error: Field [D128] at bit offset/length 128/1024 exceeds size of target Buffer (160 bits) (20180531/dsopcode-201)

                                    [    6.403962] ACPI Error: Method parse/execution failed \HWMC, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.403975] ACPI Error: Method parse/execution failed \_SB.WMID.WMAA, AE_AML_BUFFER_LIMIT (20180531/psparse-516)

                                    [    6.430705] videodev: Linux video capture interface: v2.00

                                    [    6.433530] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:08.1/0000:03:00.1/sound/card0/input9

                                    [    6.433654] input: HD-Audio Generic HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:08.1/0000:03:00.1/sound/card0/input10

                                    [    6.470201] acer_wmi: Acer Laptop ACPI-WMI Extras

                                    [    6.470211] acer_wmi: Unsupported machine has AMW0_GUID1, unable to load

                                    [    6.475879] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC295: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker

                                    [    6.475883] snd_hda_codec_realtek hdaudioC1D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)

                                    [    6.475885] snd_hda_codec_realtek hdaudioC1D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)

                                    [    6.475887] snd_hda_codec_realtek hdaudioC1D0:    mono: mono_out=0x0

                                    [    6.475888] snd_hda_codec_realtek hdaudioC1D0:    inputs:

                                    [    6.475890] snd_hda_codec_realtek hdaudioC1D0:      Mic=0x19

                                    [    6.475892] snd_hda_codec_realtek hdaudioC1D0:      Internal Mic=0x12

                                    [    6.535499] r8822be: module is from the staging directory, the quality is unknown, you have been warned.

                                    [    6.617296] input: HD-Audio Generic Mic as /devices/pci0000:00/0000:00:08.1/0000:03:00.6/sound/card1/input11

                                    [    6.669682] input: HD-Audio Generic Headphone as /devices/pci0000:00/0000:00:08.1/0000:03:00.6/sound/card1/input12

                                    [    6.707228] Bluetooth: Core ver 2.22

                                    [    6.707266] NET: Registered protocol family 31

                                    [    6.707267] Bluetooth: HCI device and connection manager initialized

                                    [    6.707274] Bluetooth: HCI socket layer initialized

                                    [    6.707278] Bluetooth: L2CAP socket layer initialized

                                    [    6.707289] Bluetooth: SCO socket layer initialized

                                    [    6.748150] [drm] amdgpu kernel modesetting enabled.

                                    [    6.752929] uvcvideo: Found UVC 1.00 device HP Wide Vision FHD Camera (04f2:b593)

                                    [    6.754527] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>

                                    [    6.760052] uvcvideo 1-4:1.0: Entity type for entity Extension 4 was not initialized!

                                    [    6.760056] uvcvideo 1-4:1.0: Entity type for entity Processing 2 was not initialized!

                                    [    6.760067] uvcvideo 1-4:1.0: Entity type for entity Camera 1 was not initialized!

                                    [    6.760257] input: HP Wide Vision FHD Camera: HP W as /devices/pci0000:00/0000:00:08.1/0000:03:00.3/usb1/1-4/1-4:1.0/input/input13

                                    [    6.761088] uvcvideo: Found UVC 1.00 device HP Wide Vision FHD Camera (04f2:b593)

                                    [    6.762851] uvcvideo: Unable to create debugfs 1-2 directory.

                                    [    6.763061] uvcvideo 1-4:1.2: Entity type for entity Extension 10 was not initialized!

                                    [    6.763077] uvcvideo 1-4:1.2: Entity type for entity Extension 12 was not initialized!

                                    [    6.763091] uvcvideo 1-4:1.2: Entity type for entity Processing 9 was not initialized!

                                    [    6.763094] uvcvideo 1-4:1.2: Entity type for entity Camera 11 was not initialized!

                                    [    6.763279] input: HP Wide Vision FHD Camera: HP I as /devices/pci0000:00/0000:00:08.1/0000:03:00.3/usb1/1-4/1-4:1.2/input/input14

                                    [    6.763672] usbcore: registered new interface driver uvcvideo

                                    [    6.763674] USB Video Class driver (1.1.1)

                                    [    6.765473] r8822be: Using firmware rtlwifi/rtl8822befw.bin

                                    [    6.772863] Parsing CRAT table with 1 nodes

                                    [    6.772873] Ignoring ACPI CRAT on non-APU system

                                    [    6.772876] Virtual CRAT table created for CPU

                                    [    6.772877] Parsing CRAT table with 1 nodes

                                    [    6.772879] Creating topology SYSFS entries

                                    [    6.772898] Topology: Add CPU node

                                    [    6.772899] Finished initializing topology

                                    [    6.773133] kfd kfd: Initialized module

                                    [    6.774158] checking generic (e0000000 7f0000) vs hw (e0000000 10000000)

                                    [    6.774163] fb: switching to amdgpudrmfb from VESA VGA

                                    [    6.783176] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'

                                    [    6.784252] r8822be: rtlwifi: wireless switch is on

                                    [    6.788599] r8822be 0000:02:00.0 wlp2s0: renamed from wlan0

                                    [    6.796304] usbcore: registered new interface driver btusb

                                    [    6.800315] Bluetooth: hci0: rtl: examining hci_ver=07 hci_rev=000b lmp_ver=07 lmp_subver=8822

                                    [    6.800321] Bluetooth: hci0: rtl: loading rtl_bt/rtl8822b_config.bin

                                    [    6.801417] Bluetooth: hci0: rtl: loading rtl_bt/rtl8822b_fw.bin

                                    [    6.803796] Console: switching to colour dummy device 80x25

                                    [    6.804258] Bluetooth: hci0: rom_version status=0 version=2

                                    [    6.804289] Bluetooth: hci0: cfg_sz 14, total size 20270

                                    [    6.804444] [drm] initializing kernel modesetting (RAVEN 0x1002:0x15DD 0x103C:0x83C6 0xC4).

                                    [    6.806146] [drm] register mmio base: 0xFE000000

                                    [    6.806148] [drm] register mmio size: 524288

                                    [    6.806176] [drm] add ip block number 0 <soc15_common>

                                    [    6.806178] [drm] add ip block number 1 <gmc_v9_0>

                                    [    6.806179] [drm] add ip block number 2 <vega10_ih>

                                    [    6.806179] [drm] add ip block number 3 <psp>

                                    [    6.806180] [drm] add ip block number 4 <powerplay>

                                    [    6.806182] [drm] add ip block number 5 <dm>

                                    [    6.806183] [drm] add ip block number 6 <gfx_v9_0>

                                    [    6.806183] [drm] add ip block number 7 <sdma_v4_0>

                                    [    6.806184] [drm] add ip block number 8 <vcn_v1_0>

                                    [    6.821439] kfd kfd: DID 15dd is missing in supported_devices

                                    [    6.821443] kfd kfd: kgd2kfd_probe failed

                                    [    6.821467] [drm] VCN decode is enabled in VM mode

                                    [    6.821467] [drm] VCN encode is enabled in VM mode

                                    [    6.821468] [drm] VCN jpeg decode is enabled in VM mode

                                    [    6.854417] [drm] BIOS signature incorrect 0 0

                                    [    6.854460] ATOM BIOS: SWBRT25890.001

                                    [    6.854500] [drm] vm size is 262144 GB, 4 levels, block size is 9-bit, fragment size is 9-bit

                                    [    6.854516] amdgpu 0000:03:00.0: VRAM: 256M 0x000000F400000000 - 0x000000F40FFFFFFF (256M used)

                                    [    6.854518] amdgpu 0000:03:00.0: GART: 1024M 0x000000F500000000 - 0x000000F53FFFFFFF

                                    [    6.854523] [drm] Detected VRAM RAM=256M, BAR=256M

                                    [    6.854524] [drm] RAM width 128bits UNKNOWN

                                    [    6.854717] [TTM] Zone  kernel: Available graphics memory: 10159338 kiB

                                    [    6.854719] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB

                                    [    6.854720] [TTM] Initializing pool allocator

                                    [    6.854725] [TTM] Initializing DMA pool allocator

                                    [    6.854769] [drm] amdgpu: 256M of VRAM memory ready

                                    [    6.854771] [drm] amdgpu: 3072M of GTT memory ready.

                                    [    6.854787] [drm] GART: num cpu pages 262144, num gpu pages 262144

                                    [    6.855352] [drm] PCIE GART of 1024M enabled (table at 0x000000F400900000).

                                    [    6.873449] [drm] use_doorbell being set to: [true]

                                    [    6.875786] [drm] Found VCN firmware Version: 1.73 Family ID: 18

                                    [    6.920894] psmouse serio1: synaptics: queried max coordinates: x [..5640], y [..4740]

                                    [    6.947784] psmouse serio1: synaptics: queried min coordinates: x [1302..], y [1116..]

                                    [    6.947794] psmouse serio1: synaptics: Your touchpad (PNP: SYN324e ETD0000 PNP0f13) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.

                                    [    6.998926] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.2, id: 0x1e2b1, caps: 0xf00123/0x840300/0x12e800/0x400000, board id: 3314, fw id: 2544170

                                    [    7.031681] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7

                                    [    7.037456] mousedev: PS/2 mouse device common for all mice

                                    [    7.210980] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: stripe=4

                                    [    7.456865] amdgpu: [powerplay] dpm has been enabled

                                    [    7.456993] [drm] DM_PPLIB: values for Invalid clock

                                    [    7.456994] [drm] DM_PPLIB: 0 in kHz

                                    [    7.456996] [drm] DM_PPLIB: 400000 in kHz

                                    [    7.456997] [drm] DM_PPLIB: 933000 in kHz

                                    [    7.456997] [drm] DM_PPLIB: 1067000 in kHz

                                    [    7.457154] WARNING: CPU: 5 PID: 401 at drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dcn_calcs.c:1355 dcn_bw_update_from_pplib+0x16b/0x280 [amdgpu]

                                    [    7.457156] Modules linked in: ext4 mbcache jbd2 fscrypto joydev mousedev btusb arc4 btrtl amdkfd btbcm amd_iommu_v2 btintel uvcvideo hid_sensor_gyro_3d hid_sensor_accel_3d hid_sensor_magn_3d hid_sensor_incl_3d hid_sensor_rotation videobuf2_vmalloc amdgpu(+) r8822be(C) videobuf2_memops bluetooth hid_sensor_trigger industrialio_triggered_buffer videobuf2_v4l2 kfifo_buf chash snd_hda_codec_realtek ecdh_generic videobuf2_common gpu_sched hid_sensor_iio_common snd_hda_codec_generic crc16 videodev snd_hda_codec_hdmi i2c_algo_bit wmi_bmof industrialio mac80211 media edac_mce_amd ttm snd_hda_intel hp_wmi sparse_keymap drm_kms_helper snd_hda_codec kvm_amd ccp rng_core snd_hda_core drm kvm snd_hwdep cfg80211 snd_pcm agpgart syscopyarea psmouse irqbypass sysfillrect snd_timer input_leds k10temp hp_accel snd

                                    [    7.457216]  rtsx_pci_ms sp5100_tco sysimgblt memstick rfkill fb_sys_fops lis3lv02d soundcore i2c_piix4 input_polldev wmi battery ac led_class i2c_hid rtc_cmos evdev i2c_scmi pinctrl_amd hp_wireless mac_hid acpi_cpufreq vboxnetflt(O) vboxnetadp(O) vboxpci(O) vboxdrv(O) msr sg crypto_user ip_tables x_tables dm_crypt dm_mod btrfs libcrc32c crc32c_generic xor zstd_decompress zstd_compress xxhash hid_sensor_hub hid_generic usbhid hid raid6_pq sd_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel pcbc ahci rtsx_pci_sdmmc serio_raw libahci atkbd libps2 mmc_core xhci_pci libata aesni_intel xhci_hcd aes_x86_64 crypto_simd cryptd glue_helper usbcore scsi_mod usb_common rtsx_pci i8042 serio lz4 lz4_compress

                                    [    7.457283] CPU: 5 PID: 401 Comm: systemd-udevd Tainted: G         C O      4.18.0-1-custom+ #6

                                    [    7.457285] Hardware name: HP HP ENVY x360 Convertible 15m-bq1xx/83C6, BIOS F.17 03/29/2018

                                    [    7.457398] RIP: 0010:dcn_bw_update_from_pplib+0x16b/0x280 [amdgpu]

                                    [    7.457399] Code: d8 ca d8 f1 d9 5a 50 8b 44 fc 14 49 8b 94 24 70 01 00 00 48 89 04 24 df 2c 24 d8 f1 db 42 78 de c9 de ca de f9 d9 5a 4c eb 02 <0f> 0b 48 89 da be 04 00 00 00 48 89 ef e8 13 5b fe ff 84 c0 0f 84

                                    [    7.457443] RSP: 0018:ffffa76803d9f7b8 EFLAGS: 00010246

                                    [    7.457446] RAX: 0000000000000001 RBX: ffffa76803d9f818 RCX: 0000000000000000

                                    [    7.457448] RDX: 0000000000000000 RSI: 0000000000000004 RDI: 00000000ffffffff

                                    [    7.457449] RBP: ffffa126300ca6c0 R08: 0000000000000001 R09: 00000000000003a0

                                    [    7.457451] R10: 0000000000000004 R11: 0000000000000000 R12: ffffa12632df1000

                                    [    7.457452] R13: ffffa12631004ec0 R14: ffffa12632df1000 R15: 0000000000000000

                                    [    7.457455] FS:  00007ffff7f85d40(0000) GS:ffffa1264ab40000(0000) knlGS:0000000000000000

                                    [    7.457457] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033

                                    [    7.457458] CR2: 00007ffff7bd4000 CR3: 00000004f85b4000 CR4: 00000000003406e0

                                    [    7.457460] Call Trace:

                                    [    7.457586]  dcn10_create_resource_pool+0x756/0x990 [amdgpu]

                                    [    7.457699]  dc_create_resource_pool+0x42/0x180 [amdgpu]

                                    [    7.457707]  ? __kmalloc+0x1aa/0x230

                                    [    7.457817]  ? dal_gpio_service_create+0x7c/0x110 [amdgpu]

                                    [    7.457924]  dc_create+0x228/0x650 [amdgpu]

                                    [    7.458031]  ? amdgpu_cgs_create_device+0x23/0x50 [amdgpu]

                                    [    7.458140]  dm_hw_init+0xc8/0x130 [amdgpu]

                                    [    7.458247]  amdgpu_device_init.cold.15+0x1041/0x1253 [amdgpu]

                                    [    7.458335]  amdgpu_driver_load_kms+0x86/0x2c0 [amdgpu]

                                    [    7.458357]  drm_dev_register+0x109/0x140 [drm]

                                    [    7.458442]  amdgpu_pci_probe+0x13c/0x1c0 [amdgpu]

                                    [    7.458448]  ? _raw_spin_unlock_irqrestore+0x20/0x40

                                    [    7.458453]  local_pci_probe+0x41/0x90

                                    [    7.458458]  pci_device_probe+0x189/0x1a0

                                    [    7.458463]  driver_probe_device+0x2b9/0x460

                                    [    7.458467]  __driver_attach+0xdd/0x110

                                    [    7.458470]  ? driver_probe_device+0x460/0x460

                                    [    7.458474]  bus_for_each_dev+0x76/0xc0

                                    [    7.458478]  bus_add_driver+0x152/0x230

                                    [    7.458482]  ? 0xffffffffc11c3000

                                    [    7.458485]  driver_register+0x6b/0xb0

                                    [    7.458487]  ? 0xffffffffc11c3000

                                    [    7.458492]  do_one_initcall+0x46/0x1f5

                                    [    7.458496]  ? kmem_cache_alloc_trace+0x181/0x1d0

                                    [    7.458500]  ? do_init_module+0x22/0x210

                                    [    7.458504]  do_init_module+0x5a/0x210

                                    [    7.458508]  load_module+0x2295/0x24b0

                                    [    7.458515]  ? vmap_page_range_noflush+0x243/0x320

                                    [    7.458521]  ? __se_sys_init_module+0x10c/0x170

                                    [    7.458524]  __se_sys_init_module+0x10c/0x170

                                    [    7.458530]  do_syscall_64+0x5b/0x170

                                    [    7.458535]  entry_SYSCALL_64_after_hwframe+0x44/0xa9

                                    [    7.458538] RIP: 0033:0x7ffff78f6f3a

                                    [    7.458539] Code: 48 8b 0d 19 cf 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 af 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d e6 ce 2b 00 f7 d8 64 89 01 48

                                    [    7.458582] RSP: 002b:00007fffffffd648 EFLAGS: 00000246 ORIG_RAX: 00000000000000af

                                    [    7.458585] RAX: ffffffffffffffda RBX: 00005555557be8e0 RCX: 00007ffff78f6f3a

                                    [    7.458587] RDX: 00007ffff7193ecd RSI: 0000000000604238 RDI: 00005555561c3c10

                                    [    7.458588] RBP: 00007ffff7193ecd R08: 0000000000000007 R09: 0000000000000006

                                    [    7.458590] R10: 00005555557b3010 R11: 0000000000000246 R12: 00005555561c3c10

                                    [    7.458591] R13: 00005555557b9c40 R14: 0000000000020000 R15: 00005555557be8e0

                                    [    7.458596] ---[ end trace 11741d28e71716a3 ]---

                                    [    7.458612] [drm] DM_PPLIB: values for Invalid clock

                                    [    7.458614] [drm] DM_PPLIB: 300000 in kHz

                                    [    7.458615] [drm] DM_PPLIB: 600000 in kHz

                                    [    7.458616] [drm] DM_PPLIB: 626000 in kHz

                                    [    7.458616] [drm] DM_PPLIB: 654000 in kHz

                                    [    7.459619] [drm:construct [amdgpu]] *ERROR* construct: Invalid Connector ObjectID from Adapter Service for connector index:2! type 0 expected 3

                                    [    7.467324] [drm] Display Core initialized with v3.1.52!

                                    [    7.474757] [drm] SADs count is: -2, don't need to read it

                                    [    7.476247] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).

                                    [    7.476249] [drm] Driver supports precise vblank timestamp query.

                                    [    7.500972] [drm] VCN decode and encode initialized successfully.

                                    [    7.503486] [drm] fb mappable at 0xD1100000

                                    [    7.503489] [drm] vram apper at 0xD0000000

                                    [    7.503491] [drm] size 8294400

                                    [    7.503492] [drm] fb depth is 24

                                    [    7.503493] [drm]    pitch is 7680

                                    [    7.503687] fbcon: amdgpudrmfb (fb0) is primary device

                                    [    7.517541] Console: switching to colour frame buffer device 240x67

                                    [    7.544515] amdgpu 0000:03:00.0: fb0: amdgpudrmfb frame buffer device

                                    [    7.553393] amdgpu 0000:03:00.0: ring 0(gfx) uses VM inv eng 4 on hub 0

                                    [    7.553397] amdgpu 0000:03:00.0: ring 1(comp_1.0.0) uses VM inv eng 5 on hub 0

                                    [    7.553400] amdgpu 0000:03:00.0: ring 2(comp_1.1.0) uses VM inv eng 6 on hub 0

                                    [    7.553403] amdgpu 0000:03:00.0: ring 3(comp_1.2.0) uses VM inv eng 7 on hub 0

                                    [    7.553406] amdgpu 0000:03:00.0: ring 4(comp_1.3.0) uses VM inv eng 8 on hub 0

                                    [    7.553409] amdgpu 0000:03:00.0: ring 5(comp_1.0.1) uses VM inv eng 9 on hub 0

                                    [    7.553411] amdgpu 0000:03:00.0: ring 6(comp_1.1.1) uses VM inv eng 10 on hub 0

                                    [    7.553414] amdgpu 0000:03:00.0: ring 7(comp_1.2.1) uses VM inv eng 11 on hub 0

                                    [    7.553417] amdgpu 0000:03:00.0: ring 8(comp_1.3.1) uses VM inv eng 12 on hub 0

                                    [    7.553420] amdgpu 0000:03:00.0: ring 9(kiq_2.1.0) uses VM inv eng 13 on hub 0

                                    [    7.553423] amdgpu 0000:03:00.0: ring 10(sdma0) uses VM inv eng 4 on hub 1

                                    [    7.553426] amdgpu 0000:03:00.0: ring 11(vcn_dec) uses VM inv eng 5 on hub 1

                                    [    7.553429] amdgpu 0000:03:00.0: ring 12(vcn_enc0) uses VM inv eng 6 on hub 1

                                    [    7.553432] amdgpu 0000:03:00.0: ring 13(vcn_enc1) uses VM inv eng 7 on hub 1

                                    [    7.553434] amdgpu 0000:03:00.0: ring 14(vcn_jpeg) uses VM inv eng 8 on hub 1

                                    [    8.096355] [drm] Initialized amdgpu 3.26.0 20150101 for 0000:03:00.0 on minor 0

                                    [   15.139148] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

                                    [   15.139151] Bluetooth: BNEP filters: protocol multicast

                                    [   15.139156] Bluetooth: BNEP socket layer initialized

                                    [   16.755073] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready

                                    [   17.322429] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready

                                    [   17.322483] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.

                                    [   17.759730] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready

                                    [   17.759779] Bridge firewalling registered

                                    [   17.909818] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready

                                    [   18.224257] fuse init (API version 7.27)

                                    [   18.426960] Initializing XFRM netlink socket

                                    [   18.563448] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready

                                    [   21.920760] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready

                                    [   21.937179] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready

                                    [   22.375748] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready

                                    [   23.755971] Bluetooth: RFCOMM TTY layer initialized

                                    [   23.755980] Bluetooth: RFCOMM socket layer initialized

                                    [   23.755990] Bluetooth: RFCOMM ver 1.11

                                    [   27.289878] core[1424]: segfault at 0 ip 0000000000441058 sp 00007fffffffd250 error 4

                                    [   27.289882] Code: 40 00 31 c0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 55 48 89 f5 53 48 89 fb 48 83 ec 08 e8 8f ec fd ff 89 c7 e8 f8 f0 fd ff <48> 8b 30 48 89 ea 48 89 df e8 fa eb fd ff 48 83 c4 08 b8 01 00 00

                                    [   33.243558] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready

                                    [   37.417237] wlp2s0: authenticate with 64:66:b3:be:b5:b7

                                    [   37.417700] wlp2s0: send auth to 64:66:b3:be:b5:b7 (try 1/3)

                                    [   37.420114] wlp2s0: authenticated

                                    [   37.420310] r8822be 0000:02:00.0 wlp2s0: disabling HT as WMM/QoS is not supported by the AP

                                    [   37.420314] r8822be 0000:02:00.0 wlp2s0: disabling VHT as WMM/QoS is not supported by the AP

                                    [   37.421043] wlp2s0: associate with 64:66:b3:be:b5:b7 (try 1/3)

                                    [   37.426414] wlp2s0: RX AssocResp from 64:66:b3:be:b5:b7 (capab=0x431 status=0 aid=4)

                                    [   37.426758] wlp2s0: associated

                                    [   37.477372] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready

                                    [27539.327236] perf: interrupt took too long (2508 > 2500), lowering kernel.perf_event_max_sample_rate to 79000

                              • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                brauliobo

                                removed the 17th family microcode and it didn't help. maybe I need to boot windows once again before a linux boot?

                                  • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                    abucodonosor

                                    brauliobo schrieb:

                                     

                                    removed the 17th family microcode and it didn't help. maybe I need to boot windows once again before a linux boot?

                                    No it won't help since your BIOS provides latest microcode already.

                                     

                                    No you don't need to boot to Windows , it won't help.

                                     

                                    ...

                                    boost state support:

                                        Supported: no <-- turbo modes not seen

                                        Active: no

                                    ...

                                     

                                    However your BIOS has some problems .. ACPI /IOMMU bugs from a quick look.

                                     

                                    Also you are using an not-yet-released custom 4.18-rcx/git kernel ,

                                    can you boot in some released one please ? 4.17.4 would be an good start.

                                     

                                    ( Please avoid loading of custom modules or using custom patches )

                                     

                                    Also what is the last working kernel for you ?

                                     

                                    Also why do you need any of these ? :

                                    rcu_nocbs=0-15 pci=noaer idle=nomwait

                                     

                                    Reporting kernel or BIOS bugs to the CPU Vendor forum won't help much in general.

                                    For kernel bugs Kernel.org Bugzilla Main Page  or the LKML ..

                                     

                                    However we can try to sort out.

                                      • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                        brauliobo

                                        `idle-nomwait` is needed to fix freezes, check epyc 7551 spontaneously resets after 10mins rendering

                                        the other cmd options I've just removed but still no frequency boost

                                         

                                        I'm using the latest 4.17 kernel at ~agd5f/linux - Unnamed repository; edit this file 'description' to name the repository. , although it was named 4.18 it is 4.17

                                         

                                        I don't remember which was the latest working kernel.

                                          • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                            abucodonosor

                                            brauliobo

                                             

                                            You don't need idle=nomwait , that's already fixed in never firmware

                                            but I don't think that ever affected your CPU.

                                             

                                             

                                            > I'm using the latest 4.17 kernel at ~agd5f/linux - Unnamed repository; edit this file 'description' to name the repository. , although it was named 4.18 it is 4.17

                                             

                                            Oh oh .. No master aka 'amd-staging-drm-next' branch is where code in dumped in.

                                             

                                            Have a look at the branch names which you have to 'pull' on top the kernel you are using.

                                            Eg: drm-fixes-<kernel-version> or drm-next-<kernel-version> , etc

                                             

                                            > I don't remember which was the latest working kernel.

                                             

                                            Well without to know what kernel worked is kind hard to say what broke that feature.

                                            Also since you updated the BIOS it may be even the BIOS itself who broke somethig.

                                              • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                                brauliobo

                                                Do you use ryzen + linux? Almost every user has been experiencing those annoying freezes!!! It was only after idle=nomwait that freezes stopped happenning. I was having usually a few everyday!

                                                 

                                                The freezes also happen in the official Archlinux kernel. I'll try 4.16 soon.

                                                 

                                                I've tried those drm-fixes-* as well. Please ask me things you know and tested before.

                                                 

                                                It can't be the BIOS, as I said before that it works under Windows 10!

                                                  • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                                    abucodonosor

                                                    brauliobo schrieb:

                                                     

                                                    Do you use ryzen + linux? Almost every user has been experiencing those annoying freezes!!! It was only after idle=nomwait that freezes stopped happenning. I was having usually a few everyday

                                                     

                                                    In fact I don't own any Windows box since 2002 myself , so yes I use Linux on / for everything.

                                                     

                                                    Ok so use idle=nomwait and hope HP fixes that sometimes since AMD pushed out an fix since a long time now.

                                                     

                                                    ( Also if you look closer to epyc 7551 spontaneously resets after 10mins rendering , you'll notice

                                                    I'm one of those guys who helped to find the issue )

                                                     

                                                    I've tried those drm-fixes-* as well. Please ask me things you know and tested before.

                                                     

                                                     

                                                    I'm not sure I understand what you mean?

                                                     

                                                    I do know what I'm talking about ..

                                                    I build myself like 30++ kernels a day , including those from amd-drm-* branches ( and lots more ).

                                                     

                                                    It can't be the BIOS, as I said before that it works under Windows 10!

                                                     

                                                    That is wrong.

                                                     

                                                    Please look closer your dmesg and then you'll notice this:

                                                     

                                                    'ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored'

                                                     

                                                    That means the follwoing:

                                                     

                                                    Your BIOS Vendor , in this case HP , is doing different 'things' for different OS'es.

                                                    What those 'things' are can be partially decoded from an acpi dump of your machine

                                                    but most probably some parts are hiddedn in the firmware so one just can guess.

                                                     

                                                    Linux follows ACPI standards where such an 'do things for one OS this way or better while

                                                    different or worse for an other one' should not exists , even when possible.

                                                    Therefore Linux itself 'ignore's any call to _OSI(Linux) by default.

                                                     

                                                    That's means again while your BIOS may work fine on Windows

                                                    it may not work at all on different OS.

                                                     

                                                    Also before that bug there are some other ones and after that bug there folows much more ACPI errors.

                                                     

                                                    Here is what you can try. Boot with the following appended to your kernel command line:

                                                     

                                                    acpi_osi=Linux acpi_osi='!Windows 2012'

                                                     

                                                      • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                                        brauliobo

                                                        Thank you abucodonosor.

                                                         

                                                        Just tried and unfortunetely still not reaching higher frequencies.

                                                         

                                                        ~ LANG=en sudo cpupower frequency-info
                                                        analyzing CPU 0:
                                                          driver: acpi-cpufreq
                                                          CPUs which run at the same hardware frequency: 0
                                                          CPUs which need to have their frequency coordinated by software: 0
                                                          maximum transition latency:  Cannot determine or is not supported.
                                                          hardware limits: 1.60 GHz - 2.00 GHz
                                                          available frequency steps:  2.00 GHz, 1.70 GHz, 1.60 GHz
                                                          available cpufreq governors: performance schedutil
                                                          current policy: frequency should be within 1.60 GHz and 2.00 GHz.
                                                                          The governor "schedutil" may decide which speed to use
                                                                          within this range.
                                                          current CPU frequency: 2.00 GHz (asserted by call to hardware)
                                                          boost state support:
                                                            Supported: no
                                                            Active: no
                                                            Boost States: 0
                                                            Total States: 3
                                                            Pstate-P0:  2000MHz
                                                            Pstate-P1:  1700MHz
                                                            Pstate-P2:  1600MHz

                                                         

                                                        ~ cat /proc/cmdline
                                                        BOOT_IMAGE=/vmlinuz-linux-custom root=UUID=7bec7995-3557-480d-aee8-d9871405748d rw pci=noaer idle=nomwait acpi_osi=Linux "acpi_osi=!Windows 2012"

                                                         

                                                        ~ less /proc/cpuinfo | grep MHz
                                                        cpu MHz         : 1994.438
                                                        cpu MHz         : 1994.462
                                                        cpu MHz         : 1994.932
                                                        cpu MHz         : 1994.941
                                                        cpu MHz         : 1995.470
                                                        cpu MHz         : 1995.480
                                                        cpu MHz         : 1995.461
                                                        cpu MHz         : 1995.463

                                                         

                                        • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                          brauliobo

                                          Also important to note that I did a few BIOS updates as HP were releasing them. I'm using the latest, F17 for this notebook model

                                          • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                            brauliobo

                                            The performance was also much better before. Currently:

                                            ~ LANG=en dd if=/dev/zero bs=1M count=1024 | md5sum
                                            1024+0 records in
                                            1024+0 records out
                                            1073741824 bytes (1.1 GB, 1.0 GiB) copied, 3.07016 s, 350 MB/s
                                            cd573cfaace07e7949bc0c46028904ff  -

                                            Before it used to return around 650mb/s, so very likely the frequency limitation is causing the general system slowdown.

                                            @abucodonosor

                                              • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                                abucodonosor

                                                brauliobo schrieb:

                                                 

                                                The performance was also much better before. Currently:

                                                ~ LANG=en dd if=/dev/zero bs=1M count=1024 | md5sum
                                                1024+0 records in
                                                1024+0 records out
                                                1073741824 bytes (1.1 GB, 1.0 GiB) copied, 3.07016 s, 350 MB/s
                                                cd573cfaace07e7949bc0c46028904ff -

                                                Before it used to return around 650mb/s, so very likely the frequency limitation is causing the general system slowdown.

                                                @abucodonosor

                                                 

                                                Yes it will cause some slowdown but not 50% ..

                                              • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                                _blackbishop_

                                                What motherboard?

                                                You have latest BIOS installed? Or you upgraded it before you started to have issues?

                                                 

                                                I had similar case when I was using older BIOS - most likely it was broken ACPI.

                                                • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                                  brunosalezze

                                                  I also have an HP x360 Envy 15z with a 2500U model 2017.

                                                   

                                                  Right now, i just did an clean install (as clean as possible) on ubuntu 18.04.1

                                                   

                                                  And its turboing as expected, top 3.6Ghz single core load.

                                                   

                                                  I have the latest bios in the HP support site.

                                                  • Re: Ryzen 2500u limited to max. 2000mhz in Linux
                                                    brauliobo

                                                    Found the issue. If I enable the HDD with Windows that enables the EFI bootloader, then the turbo mode doesn't work.

                                                    If the Legacy bootloader is enabled and the EFI bootloader isn't, then turbo frequencies work normally.

                                                    Just need a way now handle turbo frequencies with EFI.