Discussions

[Nikols_80]

чего то не хватает

[Nikols_80]

продавец говорит что это типа оригинальный процессор я в этом засомневался

[BigAl01]

You are taking a static electricity risk by placing that CPU directly on a carpet.  It could be damaged already just from that.

[BigAl01]

My earlier reply seems to have disappeared.  I responded to your question about whether that CPU is a real one or a fake.  It looks real, except that it says 'made in China'.  My 7800X3D says 'made in Malaysia'.  I might have seen AMD CPUs that said 'made in Taiwan' but I don't remember seeing 'made in China' before.

[Nikols_80]

Привет там странность не только в надписях,на текстолите процессора в верхней части не хватает контактных площадок как у оригинальных 7950 X если сравнить различия бросаются в глаза настоящийподделка 

[BigAl01]

Translation:  

Hello, there is a strange thing not only in the inscriptions, on the processor PCB in the upper part there are not enough contact pads like the original 7950 X, if you compare the differences are striking

Yes, something is fishy about that CPU.  Did you end up buying it?  If so, have you tried using it with an AM5 socket motherboard? 

[Nikols_80]

ПРивет,я собираю комп по частям и материнку ещё не купил ,поэтому нет не проверял я нашёл такого же мутанта на али экспресс .

[BigAl01]

Keep posting here as you get more parts for the build.  We are all interested if that CPU is the real thing or a fake.

[Nikols_80]

Привет,я вернул это недоразумение обратно продавцу буду брать бокс версию там не должно быть подвоха.

[BigAl01]

Translation:  

Hello, I returned this misunderstanding back to the seller, I will take the boxed version, there should be no catch.

Good idea.  The boxed versions with the AMD seal are the best way to ensure the real product is in the box. 

[Galexman]

Привет, какой код на боксовом проце у тебя? BQ 23/22? Я так понял что отсутсвие и так пустующих контактов было сделано специально на всех свежих камнях, выпущенных с начала 24-го года

[BigAl01]

Translation:

Hello, what code do you have on the box process? BQ 23/22? I understand that the lack of already empty contacts was done specifically on all fresh stones released since the beginning of 24

[Nikols_80]

привет номер такой BQ2332PGE 

[BigAl01]

hi the number is BQ2332PGE

[Nikols_80]

КАК-ТО ТАК

[KOA-SCP01]

It'll work. kaktawotkakta-TAKT

[Nikols_80]

 сработало

 

[BigAl01]

Nice, you got it built.  Am I seeing 324 frames per second in War Thunder or am I reading the Russian wrong?

[Nikols_80]

Да всё верно он быстрый,.))

[BigAl01]

Translation -

Yes, that's right, he's fast.)) 

[Nikols_80]

Сработало я собрал новый комп всё супер

[BigAl01]

Translation:

It worked, I assembled a new computer, everything is super 

Well, congratulations @Nikols_80 !  There is nothing quite as exciting as the first boot of a new computer build, except for maybe the birth of your first child or getting your college degree.  

If you have a chance, please post a few more pictures of your completed build.  Tell us if you had any difficulty building it too.  Lots of people have problems getting drivers to work or making the correct settings in the motherboard BIOS so the system is fast and stable.

[Nikols_80]

спасибо за поздравления BigAl01 .Небольшие трудности возникли при монтаже видеокарты,крепление к корпусу куда вкручивается винт оказалось выше на 1.5мм  карта не вставала в разъем его пришлось доработать напильником что прискорбно учитывая стоимость корпуса,в остальном всё прошло без проблем,BIOS в режиме turbo boost больше ничего не менял .Stalker 2 работает на эпичных настройках без upscaling средняя частота кадров 80 в секунду.Я доволен производительностью системы очень.

[BigAl01]

Translation:

Thank you for the congratulations BigAl01. Slight difficulties arose during the installation of the video card, the fastening to the case where the screw is screwed turned out to be higher by 1.5mm, the card did not fit into the connector, it had to be modified with a file, which is regrettable given the cost of the case, otherwise everything went without problems, the BIOS in turbo boost mode did not change anything else. Stalker 2 runs on epic settings without upscaling an average frame rate of 80 per second.

That's good to hear.  When I build my own cases, mounting the video card is always an issue to deal with.  For my last build (Wine-Cool), I made a support bracket out of aluminum bar and mounted that to another aluminum bar in the frame I assembled. 

This assembly is laying on it's side. You can see the bracket I made to support the video card.

In the past, as in 2005, I used a hacksaw blade for a support bar when I built my 'Printer to Computer' that was featured in Maximum PC magazine as Rig of the Month.  They didn't know that I had broken a few hacksaw blades when trying to bend them - they are brittle as I found out.  Live and learn. 

Three blades were used to support the video card here. Two were twisted and I broke a few of those.

[Nikols_80]

Привет твой win-cool выглядит практично ничего лишнего, Я бы посоветовал прикрепить кулер к backplate комп скажет спасибо лишним фпс. 

[BigAl01]

Translation:

Hi your wine-cool looks practical, nothing superfluous, I would advise attaching the cooler to the backplate, the computer will say thank you to the extra fps.

Response:

The AIO is connected to the CPU and the radiator vents through the top of the wine cooler case.  It runs nice and cool actually.  It's my best performing computer out of about 12 machines on my LAN.

You can see the AIO venting warm air through the top of the case in this picture.

[Nikols_80]

 

 

 

 

Привет BigAl01 кулеров много не бывает

 

 

 

 

[BigAl01 · Accepted solution]

That case is similar to a Thermaltake open frame design, but it's different.  Is it made in Russia?

I've never seen so many zip ties used in a computer build.  Why not use the screws to hold things in place?