Processors

[janerik]

I recently updated my ASUS Prime B350-Plus' BIOS from version 0808 (2017/09/15) to 3803 (2018/01/26).

I didn't expect the update to wipe all settings, but that is what just happened. Countless hours of RAM OC burned for nothing.

But that isn't the worst part. I intend to run my Ryzen 5 1600 at 3,85GHz, but after just one minute into Windows, Task-Manager and CPU-Z state, that my CPU is downclocked to 1,33GHz. Whatever causes this also disables cores at will. As I am writing this post, only 2 of the 6 cores are marked to be active. I know this form of downclocking exists to help my CPU survive longer, but even under heavy load it just bounces back up to max. 1,8GHz and ingame-performance is very poor. I downgraded myself from 50-80FPS in some games to like 20FPS.

What can I do, as the Flash Utility does not allow downgrades? I am very unsure what to do next.

Thanks, Jan.

[aquatica]

Not sure if this is going to help, but there seems to be a new BETA version of the UEFI available as well?

Version 3805 Beta Version 2018/02/11

That's on the Download page at least...?

Also what I suggest is to download it, copy to USB stick, restart into UEFI, reset all settings to factory defaults and then flash the thing through UEFI.

[janerik]

This actually leaded to better performance overall. The problem got somewhat fixed, but returned after Windows was set into Sleep Mode. Was very weird. After I changed all settings to those suggested from a.l.i.​ everything worked again like a charm.

Thank you guys =)

[janerik]

Edit: Will save my BIOS profiles to external drive from now on. Can only suggest that to everyone.

[a_l_i_ · Accepted solution]

Try this bios setup :

• Ai Overclock Tuner [Auto]
• Memory Frequency [DDR4-3066MHz]
• Custom CPU Core Ratio [Auto]
• > CPU Core Ratio [37.00]
• EPU Power Saving Mode [Disabled]
• OC Tuner [Keep Current Settings]
• Performance Bias [Auto]
• VDDCR CPU Voltage [Offset mode]
• VDDCR CPU Offset Mode Sign [+]
• VDDCR CPU Offset Voltage [0.01875]
• VDDCR SOC Voltage [Offset mode]
• VDDCR SOC Offset Mode Sign [+]
• VDDCR SOC Offset Voltage [0.05000]
• DRAM Voltage [1.38000]
• 1.05V SB Voltage [Auto]
• 2.5V SB Voltage [Auto]
• CPU 1.80V Voltage [Auto]
• VTTDDR Voltage [0.77000]
• VPP_MEM Voltage [2.55000]
• VDDCR CPU Load Line Calibration [Medium]
• VDDCR SOC Load Line Calibration [High]
• VDDCR CPU Power Phase Control [Optimized]
• VDDCR CPU Switching Frequency [300]
• Target TDP [Auto]
• Mem Over Clock Fail Count [Auto]
• DRAM CAS# Latency [18]
• Trcdrd [18]
• Trcdwr [18]
• DRAM RAS# PRE Time [18]
• DRAM RAS# ACT Time [40]
• Trc_SM [58]
• TrrdS_SM [Auto]
• TrrdL_SM [Auto]
• Tfaw_SM [Auto]
• TwtrS_SM [Auto]
• TwtrL_SM [Auto]
• Twr_SM [Auto]
• Trcpage_SM [Auto]
• TrdrdScl_SM [Auto]
• TwrwrScl_SM [Auto]
• Trfc_SM [Auto]
• Trfc2_SM [Auto]
• Trfc4_SM [Auto]
• Tcwl_SM [Auto]
• Trtp_SM [Auto]
• Trdwr_SM [Auto]
• Twrrd_SM [Auto]
• TwrwrSc_SM [Auto]
• TwrwrSd_SM [Auto]
• TwrwrDd_SM [Auto]
• TrdrdSc_SM [Auto]
• TrdrdSd_SM [Auto]
• TrdrdDd_SM [Auto]
• Tcke_SM [Auto]
• ProcODT_SM [53.3 ohm]
• Cmd2T [1T]
• Gear Down Mode [Disabled]
• Power Down Enable [Auto]
• RttNom [Auto]
• RttWr [Auto]
• RttPark [Auto]
• MemAddrCmdSetup_SM [Auto]
• MemCsOdtSetup_SM [Auto]
• MemCkeSetup_SM [Auto]
• MemCadBusClkDrvStren_SM [Auto]
• MemCadBusAddrCmdDrvStren_SM [Auto]
• MemCadBusCsOdtDrvStren_SM [Auto]
• MemCadBusCkeDrvStren_SM [Auto]

[nabby]

Same mobo and CPU here.
Is that CPU voltage offset correct? On CPU-Z and HWMon I'm getting everything slightly different than what it's set at anyway, but with these settings I'm getting maximum 3694mhz on all cores @ 1.269V (which is only getting up to 61C on my cooler) and wanting to increase a bit. I'm new to using offsets and not sure how much of an effect it has, but 0.01875 seems pretty tiny and I'm hoping to try 3.9ghz @ 1.3 - 1.35 V.