I had looked on many forums, and I can not fint a work around this.
When I do 3Dmark , it reach max Clocks, but in battlefield, it only do it when I am in Menu.
When Iam playing any mode or Firestorm it don't go max on clocks, and I see some people with newer hardware, have higher clock and better fps on Ultra.
Is my cpu the reason it doesn't pump max Fps and max clock?
I can see it sit on 900-1200mhz GPU clock and it have around 90-100 fps instead of going max on clock and fps.
I have a 144hz monitor and Ingame settings is low beside Mesh is on Ultra.
Thanks you in advance
Hey this is my Spec:
PSU: 1200W corsair Plat, new only weeks old.
CPU is OC. to 4.2Ghz.
GPU :MSI Radeon-RX-Vega-64-Air-Boost-8G-OC
Must sad part of this is, I could have went green after being red all this time, buying and waiting for long, I have a r9 290x OC, with Water block that can do matter then this. It's so sad, so big numbers before release and after release ..... Navi not going to do any different, mark my word. All the hype and when it come out it be under Greenteam.
Unfortunately your RX Vega 64 is a reference cooler design. What temperature does the GPU hit when you play BFV?
It is likely not keeping cool enough and likely throttling. The HBM2 frequency is set high which is good.
Are those the default GPU Clock frequency curve or did you mod it?
Try setting your GPU fan PWM to 100%, put a pair of headphones on first though - does that help the FPS?
Are you certain which position the BIOS switch is set to?
One position is low power BIOS and the other is high performance BIOS setting, It makes a difference to performance.
What resolution are you running at?
it was set to the other side(left), now Iam setting it to right and will play some around and then set it to max fan speed and play and see if it does make any different but how to see what profile is max? since both Bios profile perform same high level 1620mhz clock in 3dMark.
And yes its modified I clocked it abit more, (undervolted it), used 3 days to find sweat spot with good score and stable system, but for some reason it do 1620mhz in menu (Battlefield) where there is some soldiers and tanks and moving stuff, vs ingame online.
I am tired of having this performance, so it can do 1400- max out 1630MHz in the Menu but when I play?????
And it do small fps drop in 1v1 fight, where it so much matter. My R9 290x I could get more out of that. So I wait this long to get a Vega card and I get this. Wasting days on wondring what I did wrong.
I run DX11 in Battlefield, but In Apex no issue, so Battlefield is broke?
Avg Temp, Clock .... And below this is Max.
Normaly switch towards the faceplate with the display outputs is the primary high performance BIOS. Setting it to the right is the secondary BIOS. However ... someone could have swapped the BIOSes around or MSI may do it different. Easiest thing to try is run 3DMark Timespy and monitor the GPU power.
Boost Clock / Base Clock / Memory Frequency
up to 1575 MHz / 1272MHz / 945 MHz
MSI are claiming peak Boost Clock of 1575MHz, with a base clock of 1272MHz and rated HBM2 speed of 945 MHz.
It is a 2 slot reference cooler. To get more performance out of that Vega 64 you would have to watercool it or add an AIO cooler.
I just played a around with DX12, wired, because it was hitting max Clock, but It had more lag spikes randomly, as this is a known issue that DX12 is not stable for many with even DX12 cards, and Iam running all off/low, beside Mesh and Post Process Quality med or high, since in the new Battleroyal Firestorm. The Scope in view on scope (Rifles and Snipers is getting blure view in the scope.
Any Idea why DX11 force it to run lower?
The Alphacool Eiswolf is sold out, and I not sure what else I should go for, either I see total pipe system that cost alot or it's not on stock in EU.
I have Kraken G12 + Kraken x42 from Nzxt on my R9 290x. But Iam pretty sure it won't match. 😕
AMD GPU's have a high driver overhead / are less capable of sheduling and running DX11 code efficiently across multiple CPU threads
The majority of the AMD Driver overhead runs on one CPU, usually CPU 0.
You might want to make sure that you have as few processes running as possible.
Try overclocking the CPU.
Other than that there is not much you can do.